> Also - you are unlikely to put your wrench inside the tower to tighten the
> bolt. You want to turn the nut when tightening - turning the bolt will
> ream
> the galvanizing from the hole.
That's why I use a ratchet and deep well socket. I find the bolts sticking
out on a ROHN 45G to be hazardous, so all of mine have the nuts on the
inside.
As my tower is climbed often and the torque checked about once a year I have
little concern about a nut coming off. The only short coming I find is if I
want to bring the coax cables and control cables down the inside of a leg.
Then it takes some precautions going around the bolts.
Roger Halstead (K8RI and ARRL 40 year Life Member)
N833R - World's oldest Debonair CD-2
www.rogerhalstead.com (Use return address from home page)
>
> 73,
> Joe
> kk0sd
>
> ----- Original Message -----
> From: "Ken Shutt" <kgshutt@cox.net>
> To: <wc1m@msn.com>; "'Roger D Johnson'" <n1rj@adelphia.net>
> Cc: "Tower" <towertalk@contesting.com>
> Sent: Monday, August 28, 2006 6:50 PM
> Subject: Re: [TowerTalk] Rohn tower bolts
>
>
>> Again, I concur.
>>
>> Ken - W5KQ
>>
>> ----- Original Message -----
>> From: "Dick Green WC1M" <wc1m@msn.com>
>> To: "'Roger D Johnson'" <n1rj@adelphia.net>
>> Cc: "Tower" <towertalk@contesting.com>
>> Sent: Sunday, August 27, 2006 11:45 PM
>> Subject: Re: [TowerTalk] Rohn tower bolts
>>
>>
>>>> > What's the deal with putting the bolts in the way Rohn specifies?
>>>
>>> N1RJ wrote:
>>>
>>>> The reason is that it's much easier to spot a missing nut if
>>>> it's on the outside. A bolt that is inserted from the bottom
>>>> and missing it's nut will fall out and the resulting hole
>>>> will be obvious to anyone climbing the tower.
>>>
>>> Aha! That phrasing rings a bell. I knew I'd seen something about this in
>>> writing somewhere. Check out page 33 of the 3rd edition of "Tower
>>> Climbing
>>> Safety and Rescue", available from ARRL. It talks about checking tower
>>> bolts
>>> before climbing, and says pretty-much what Roger said. However, the
>>> comments
>>> specifically refer to angle steel towers with members that are bolted
>>> together. The text says hollow rod or round construction presents a
>>> different set of unique inspection issues (like checking weep holes to
>>> make
>>> sure they're open and not leaking a lot of rust.)
>>>
>>> I'm not so sure missing nuts would be more obvious inside or outside a
>>> Rohn
>>> 25/45/55 tower. I climbed a friend's 100' Rohn 45 tower yesterday and I
>>> have
>>> a clear mental image of the nuts on the inside of the tower, yet I can't
>>> picture the bolt heads on the outside of the tower. When you climb a
>>> tower
>>> like this, you can see all three inside faces, but one outside face is
>>> away
>>> from you. Perhaps on this type of tower it's better to insert the bolts
>>> outside-in, like it seems just about everyone on this reflector has
>>> done.
>>>
>>> Consensus?
>>>
>>> 73, Dick WC1M
>>>
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>>
>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|