Living 900' from the ocean, when I'm done it all gets a spray on clear.
Several actually.
I have had my 2M, 440, & A3S up on tower one for about 5 years now and they
still look good. That's unheard
of beachside in Daytona.
73 Dave
www.n4zkf.com
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of James C. Hall, MD
Sent: Sunday, July 06, 2008 8:22 PM
To: 'David Calder'; towertalk@contesting.com
Subject: Re: [TowerTalk] Aluminum tarnish removal
Great stuff, David. I'm writing all this down !
73, Jamie
WB4YDL
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of David Calder
Sent: Sunday, July 06, 2008 6:44 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Aluminum tarnish removal
600 Wet/Dry sandpaper and put the element in a drill. Run the sandpaper up
and down the element.
Shines them right up.
73 Dave n4zkf
www.n4zkf.com
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Larry WA9VRH
Sent: Sunday, July 06, 2008 7:39 PM
To: James C. Hall, MD; 'TowerTalk List'
Subject: Re: [TowerTalk] Aluminum tarnish removal
Hi Jamie,
I have had good luck with S.O.S. steel wool soap pads. I know people get
freaked out about the steel part but I never found that to be an issue.
Cleaned up a couple of TA-33's and also a 40' Heights Aluminum towers. This
was a real mistake but once I started I had to finish as it looked so good I
had no choice!
73 Larry WA9VRH
----- Original Message -----
From: "James C. Hall, MD" <heartdoc@nwtcc.com>
To: "'TowerTalk List'" <towertalk@contesting.com>
Sent: Sunday, July 06, 2008 6:21 PM
Subject: [TowerTalk] Aluminum tarnish removal
> Hi All:
>
>
>
> I noticed this past FD that my F12 C3S had a bit of tarnish that was
> causing some resistance when trying to nest the tubes after the event.
> I know I probably should have been doing this all along, but what is
> the consensus on aluminum oxidation and tarnish removal ? I've tried
> Scotchbrite pads, Brasso, and Maaso metal polish. The Brasso works the
> best but really takes some elbow grease. I worked for a few hours
> today and got a couple of elements looking reasonable but with a few
> residual tarnish spots. I was beat after that !
>
>
>
> There's got to be a better way. I have some Tarn-X, but it says not to
> use it on aluminum.
>
>
>
> Thanks,
>
>
>
> Jamie
>
> WB4YDL
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
No virus found in this incoming message.
Checked by AVG - http://www.avg.com
Version: 8.0.134 / Virus Database: 270.4.4/1532 - Release Date: 7/3/2008
8:32 AM
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|