Towertalk
[Top] [All Lists]

Re: [TowerTalk] Crimp Tool for LMR-600

To: "'Tower and HF antenna construction topics.'" <towertalk@contesting.com>
Subject: Re: [TowerTalk] Crimp Tool for LMR-600
From: "James C. Hall, MD" <nwtcc@earthlink.net>
Reply-to: "Tower and HF antenna construction topics." <towertalk@contesting.com>
Date: Thu, 11 Mar 2010 21:28:36 -0600
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Roger:

Davis RF doesn't have such an item on their web site. If you can tell me
where to get one of these piston crimpers for less than a C note, I'm in.
I'll get my own instead of bugging my cell comm. guy.

73, Jamie
WB4YDL

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Roger (K8RI)
Sent: Thursday, March 11, 2010 8:54 PM
To: Tower and HF antenna construction topics.
Cc: vic.w4vic@verizon.net
Subject: Re: [TowerTalk] Crimp Tool for LMR-600



James C. Hall, MD wrote:
> Hi Vic:
>
> Normally I use a piston-type crimper for LMR-600 with a precision die.
This
> isn't cheap and runs about $300. Check out RF Parts -
>   
I also use the piston type for LMR-600 but it was well less than $100. I 
don't remember where I purchased that one, but it might be worthwhile to 
check with Steve Davis to see what they might have.  I use a more or 
less standard type with interchangeable dies for RG58, 8X, 8, LMR400, 
etc and then the piston type for LMR600.

73

Roger (K8RI)
> http://www.rfparts.com/coax_accessories.html . I usually can borrow one
from
> my local cell communications shop owner who happens to also be a ham. :)
>
> 73, Jamie
> WB4YDL
>
> -----Original Message-----
> From: towertalk-bounces@contesting.com
> [mailto:towertalk-bounces@contesting.com] On Behalf Of Vic Culver
> Sent: Thursday, March 11, 2010 2:09 PM
> To: Tower Talk Reflector
> Subject: [TowerTalk] Crimp Tool for LMR-600
>
> Gentlemen, there are two adverts in QST magazine offering "Commercial 
> Grade" ratcheting crimp tools with two dies for LMR-400, 9913, RG-213, 
> etc. coax cable at sale prices (list price $100.00).  I am unaware as to 
> whether an additional die can be purchased to accommodate LMR-600 cable 
> and would call to inquire except that I've been 'warned off' this 
> product by someone who purchased a similar device and discovered that 
> the die does not close properly resulting in 'loose crimp connections.'
>
> Does anyone here have specific experience with these (or this type) of 
> crimp tool and, if so, what would your advice be to someone looking for 
> casual use of such a tool?
>
> Thanks in advance for any comment you care to make.  73,  Vic, W4VIC
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> No virus found in this incoming message.
> Checked by AVG - www.avg.com 
> Version: 9.0.733 / Virus Database: 271.1.1/2736 - Release Date: 03/11/10
> 01:33:00
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>   
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk




E-mail message checked by Spyware Doctor (7.0.0.514)
Database version: 6.14540
http://www.pctools.com/en/spyware-doctor-antivirus/





E-mail message checked by Spyware Doctor (7.0.0.514)
Database version: 6.14540
http://www.pctools.com/en/spyware-doctor-antivirus/
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>