[CQ-Contest] Coax Stubs for SO2R
Joe
nss at mwt.net
Tue Jul 26 11:42:10 EDT 2016
That coax was stuff that I wouldn't even use on 160 meters.
Outside for decades with nothing on the ends.
Strip it back and braid as well as center conductor BLACK!
Scrape with a knife to make shiny copper show so solder will stick, and
that it.
The badly contaminated sure doesn't seem to effect it's effectiveness as
seen in that video.
Joe WB9SBD
Sig
The Original Rolling Ball Clock
Idle Tyme
Idle-Tyme.com
http://www.idle-tyme.com
On 7/26/2016 10:36 AM, Rudy Bakalov wrote:
> How do you guys do that? That is, how do you end up with all that coax
> without buying it? Or the connectors? I have purchased about 500' of
> LMR600 and maybe another 500' in LMR400 Flex. The Big Bang didn't pile
> up any coax in my back yard :-(
>
> Rudy N2WQ
>
> Sent using a tiny keyboard. Please excuse brevity, typos, or
> inappropriate autocorrect.
>
>
> On Jul 26, 2016, at 10:52 AM, Joe <nss at mwt.net <mailto:nss at mwt.net>>
> wrote:
>
>> I agree,
>> If I have 5 bucks invested in my stubs I'd be amazed!
>> And as shown before for less than 5 bucks they seem to work awful well.
>> https://youtu.be/wgn_L_LUXcI
>>
>> Joe WB9SBD
>> Sig <CLEAN-IDLE-TYME-LOGO-120x96.jpg>
>> The Original Rolling Ball Clock
>> Idle Tyme
>> Idle-Tyme.com <http://idle-tyme.com>
>> http://www.idle-tyme.com
>> On 7/26/2016 9:37 AM, Jeff AC0C wrote:
>>> I would guess most guys don't go to this much effort. New stuff and
>>> optimized placement? Wow, that would be cool!
>>>
>>> I built the stubs up on an as-needed basis with whatever I had
>>> laying about; there's no LMR400 around here. It's all RG-11 or
>>> 213. 213 has a bit better attenuation dip and is more rugged. All
>>> of the T connectors were Chinese specials initially and later most
>>> were swapped with AMP parts that I ran across at swaps and
>>> hamfests. Never blew up a Chinese one though so can't say the 50
>>> year old AMP are better.
>>>
>>> The stubs are hanging off of the existing tower-based 2x6 antenna
>>> switch which feeds a bunch of monobanders so no additional switching
>>> was needed. I did not optimize the placement; had room for them and
>>> it was easy to do so they went out there.
>>>
>>> They live in a metal trash (no UV/mouse problems like plastic) can
>>> which is staked to the ground (so it does not blow away in the big
>>> winds we get). There is a foot of some sort of Styrofoam stuff at
>>> the bottom so if the thing ever starts taking on water for some
>>> reason, it won't leave them swimming. Although if you seal the stub
>>> ends, it's not a problem either. I went with the metal after going
>>> out one time to check how the stuff looked before fall and found my
>>> stubs tub half full of water. I think that was a week or two after
>>> CQWW RTTY one year... Got lucky nothing blew up there!
>>>
>>> I measure the isolation with a vna at the shack. If I think I need
>>> more attenuation, then I build another stub and grab a 1/8 wave (or
>>> whatever is close) to space it away from the current one and turn my
>>> single stub into a pair.
>>>
>>> I don't hear my other radios at all except on the 40/20m combo.
>>> Added another stub and the level did not drop which is a possible
>>> clue that there may be something on my 40m 4-square that's
>>> generating it's own harmonics when hit with some power (which if you
>>> have seen my 4-square you can EASILY believe that...). I do have a
>>> set of 5b4agn filters in the shack that run between the amps and the
>>> rigs which are autoswitched. The filters do a decent job of cutting
>>> down on interference and definitely keep the rigs protected, but the
>>> added stubs take the situation from a "tolerable" case to a "I don't
>>> need to worry where I am on the band" sort of thing, most of the time.
>>>
>>> Like anything in radio, if perfection is not required, costs and
>>> time invested can be scaled back quite a lot. Building a set of
>>> stubs and finding the hardware is sort of a hassle. But it's
>>> something you do one time and enjoy for a long run.
>>>
>>> 73/jeff/ac0c
>>> www.ac0c.com
>>> alpha-charlie-zero-charlie
>>>
>>> -----Original Message----- From: Rudy Bakalov via CQ-Contest
>>> Sent: Tuesday, July 26, 2016 10:02 PM
>>> To: Joe
>>> Cc: Jukka Klemola ; cq-contest
>>> Subject: Re: [CQ-Contest] Coax Stubs for SO2R
>>>
>>> For me the important lesson learned from this discussion is that
>>> stubs are not as easy as snip-snip you got yourself stubs. Deploying
>>> them takes planning and careful testing. That is, takes a lot of time.
>>>
>>> I did a very quick back of the envelope calculation. In order to
>>> achieve the same level of attenuation you need two sets of stubs.
>>> Right there you have roughly 800' of LMR400. A 1000' spool is $450.
>>> Then you probably have another $100 in connectors. $550 in materials
>>> alone. And we haven't even made the stubs yet.
>>>
>>> Add the time to cut, trim, and crimp the stubs. Add the time to
>>> properly position them along the feed line. I don't know how others
>>> value their time, but I would rather spend it with the family or
>>> operate the station than spend two weekends in a spiderweb of stubs
>>> and severed feed lines.
>>>
>>> I also think proper stub placement is easier said than well done.
>>> Think about it- the SO2R remote switch is at the base of the tower
>>> and then the individual antenna feed lines go up the tower. You
>>> either have to find the ideal location up along the tower or coil
>>> tons of coax at the base.
>>>
>>> If you coil up all that coax at the base of the tower you need to
>>> build some sort of a structure to hold it.
>>>
>>> If you decide to have it up the tower then you add significant wind
>>> load surface to the tower. Not good.
>>>
>>> Of course, I may be over-engineering things, but I prefer avoiding
>>> complexity.
>>>
>>> Rudy N2WQ
>>>
>>> Sent using a tiny keyboard. Please excuse brevity, typos, or
>>> inappropriate autocorrect.
>>>
>>>
>>>> On Jul 26, 2016, at 9:12 AM, Joe <nss at mwt.net> wrote:
>>>>
>>>> Really? 200+ Euros? And coax made homebrew stubs are not much
>>>> cheaper? HUH?
>>>>
>>>> Joe WB9SBD
>>>> <CLEAN-IDLE-TYME-LOGO-120x96.jpg>
>>>> The Original Rolling Ball Clock
>>>> Idle Tyme
>>>> Idle-Tyme.com <http://idle-tyme.com>
>>>> http://www.idle-tyme.com
>>>>> On 7/25/2016 4:53 PM, Rudy Bakalov wrote:
>>>>> Jukka, Jim, and Steve,
>>>>>
>>>>> Thank you for taking the time to go into details. What's clear to
>>>>> me that the non liner AB type of amps contributes significantly to
>>>>> harmonics along with improper amp loading/tuning.
>>>>>
>>>>> As I mentioned earlier I already have BPFs so now I am left with
>>>>> the mechanical challenge of stubs. Specifically, will have to
>>>>> follow Jukka's advice on adding coax between the remote SO2R
>>>>> switch and the antennas.
>>>>>
>>>>> Honestly, I even wonder if the hassle of building and placing two
>>>>> sets of stubs (it seems the opinion is that two are needed) is
>>>>> really that much cheaper compared to buying high power BPFs.
>>>>> Between Remo's filters and the link below there are affordable
>>>>> alternatives to Ranko's BPFs:
>>>>>
>>>>> http://www.antennas-amplifiers.com/Band-Pass-Filter
>>>>>
>>>>> For €1200 one can have plug and play filtering (although I may run
>>>>> into components' thermal properties when the filters are outside
>>>>> by the tower) that is not critical with respect to placement along
>>>>> the feed line.
>>>>>
>>>>> Who sad ham radio is a hobby; feels like serious engineering work
>>>>> to me :-)
>>>>>
>>>>> Thank you all for your patience.
>>>>>
>>>>> Rudy N2WQ
>>>>>
>>>>> Sent using a tiny keyboard. Please excuse brevity, typos, or
>>>>> inappropriate autocorrect.
>>>>>
>>>>>
>>>>> On Jul 25, 2016, at 4:41 PM, Jukka Klemola <jpklemola at gmail.com>
>>>>> wrote:
>>>>>
>>>>>> Hi,
>>>>>> I try give simplified answers ...
>>>>>>
>>>>>> This should answer also Rudy's question.
>>>>>>
>>>>>>
>>>>>> 2016-07-25 15:47 GMT+03:00 Joe <nss at mwt.net>:
>>>>>>
>>>>>>> This also puzzles me.
>>>>>>> OK if an amp because of it's tuned matching circuits, block out
>>>>>>> of band
>>>>>>> energies
>>>>>>
>>>>>>
>>>>>> Amplifier circuits attenuate unwanted band energy.
>>>>>> But to a limit.
>>>>>> A Pi filter attenuates to some level, Pi-L attenuates more.
>>>>>> If that is not enough, we need additional attenuating, that is
>>>>>> additional
>>>>>> filtering like a stub
>>>>>>
>>>>>>
>>>>>> The why do we have these energies at all in the first place?
>>>>>>
>>>>>> When amplifying a signal in an amateur amplifier, the plate
>>>>>> current when
>>>>>> only PTT is activated is less than a quarter of plate current
>>>>>> with maximum
>>>>>> specified signal that is amplified.
>>>>>> It means there is plate current through most of the sine wave
>>>>>> signal cycle,
>>>>>> but not all of it.
>>>>>> It means there is a sharp corner in the output signal .. it is
>>>>>> not a clean
>>>>>> sine wave.
>>>>>> Such signal with such corners has harmonic energy.
>>>>>> This energy propagates towards the antenna connector.
>>>>>> It travels through the output circuit; most often Pi or Pi-L.
>>>>>> On an oscilloscope, the signal looks pretty much like a sine wave
>>>>>> but it
>>>>>> contains harmonic energy.
>>>>>>
>>>>>> Sorry, but this gets more complex when digging deeper.
>>>>>> Next step would require you to read some books or at least web
>>>>>> sites.
>>>>>>
>>>>>> Easy to understand information packages are ARRL hand book and
>>>>>> Orr/W6SAI
>>>>>> Radio Handbook.
>>>>>>
>>>>>> ARRL handbook is easy to find and purchase.
>>>>>> I would suggest to try and find also a paper book:
>>>>>> http://www.eham.net/reviews/detail/3963
>>>>>>
>>>>>> W2VJN book is a must if you want to understand more about RF
>>>>>> filtering
>>>>>> needs at a multi radio station.
>>>>>>
>>>>>>
>>>>>> ** Encouragement, keep it simple message:
>>>>>> As we are hams, we can use ready made recipes for stubs, among
>>>>>> many other
>>>>>> things.
>>>>>> That is allowed for us and us hams, we can just accept many
>>>>>> things as given
>>>>>> facts.
>>>>>>
>>>>>>
>>>>>> Does not a Radio have the equivalent of an "Exciter" ( the ummm
>>>>>> low level
>>>>>>> driver )
>>>>>>
>>>>>>
>>>>>>> And the "AMP" ( the final output amplifying system )
>>>>>>> So, if all this filtering is happening why do we have spurious
>>>>>>> out of the
>>>>>>> radio, but not an amp?
>>>>>>
>>>>>> There are a lot more signals in the radio than the mains input
>>>>>> and RF
>>>>>> connector with RXinput / TX output.
>>>>>> To start with, the radio's oscillator is not on your actual output
>>>>>> frequency.
>>>>>> There are other oscillators, mixers, filters, amplifier circuits,
>>>>>> more
>>>>>> filters and so on inside your transmitter before the antenna
>>>>>> connector.
>>>>>> All those are creating or limiting spurious signals and we need
>>>>>> to engineer
>>>>>> the radios so the radios do not emit unnecessary signals and we
>>>>>> engineer
>>>>>> our radios so they do not input unnecessary signals or at least
>>>>>> the radio
>>>>>> does not care about the unnecessary/unwanted signals.
>>>>>> Emissions are emissions; intended or spurious.
>>>>>> The receiving side phenomena are under words immunity or
>>>>>> susceptibility.
>>>>>> Together they are electromagnetic compatibility EMC.
>>>>>>
>>>>>> These spurious signals propagating from device to another device
>>>>>> can be as
>>>>>> bad as K1EA described about the radios they used.
>>>>>> The radio2radio signal propagation happened on a set of phenomena
>>>>>> caused by
>>>>>> some radio internal signalling leaking through radio wiring and
>>>>>> propagating
>>>>>> to another radio so the receiver of the other radio heard the
>>>>>> transmitting
>>>>>> radio signal regardless the frequencies the radios were on,
>>>>>> That is a really puzzling situation and typically difficult to
>>>>>> overcome.
>>>>>> Most likely the leaking and injecting mechanism was through antennas
>>>>>> connected to radios but not necessarily. That kind of
>>>>>> electromagnetic
>>>>>> incompatibility should be rare, though.
>>>>>>
>>>>>> After Ken K1EA et al added RF and maybe also other filtering, the
>>>>>> radios
>>>>>> stopped hearing each other that badly.
>>>>>>
>>>>>> Other filtering are for example ferrites we place on DC power
>>>>>> cords, mains
>>>>>> wires and other .. PTT / band data and any other wiring you have
>>>>>> at your
>>>>>> station. We attenuate unwanted signals until they do not bother us.
>>>>>> You can find a lot of information about different kinds of
>>>>>> filtering in the
>>>>>> internet.
>>>>>>
>>>>>> All cases are different.
>>>>>>
>>>>>> Some hands-on information here:
>>>>>> http://wiki.k1ttt.net/Default.aspx?Page=2008%20Maintenance%20and%20Upgrade%20Blog&NS=&AspxAutoDetectCookieSupport=1
>>>>>>
>>>>>>
>>>>>> Look for words
>>>>>> -harmonic
>>>>>> -power
>>>>>>
>>>>>>
>>>>>>
>>>>>>> Joe WB9SBD
>>>>>>
>>>>>>
>>>>>> 73,
>>>>>> Jukka OH6LI
>>>>>>
>>>>>>
>>>>>>> Sig
>>>>>>> The Original Rolling Ball Clock
>>>>>>> Idle Tyme
>>>>>>> Idle-Tyme.com <http://idle-tyme.com>
>>>>>>> http://www.idle-tyme.com
>>>>>>>> On 7/25/2016 5:48 AM, Rudy Bakalov via CQ-Contest wrote:
>>>>>>>> Jukka,
>>>>>>>> It is the statement below that really puzzles me. All amp
>>>>>>>> people I know,
>>>>>>>> including those that manufacture commercial amps, categorically
>>>>>>>> state that
>>>>>>>> amps do not generate harmonics on their own. That is, amps
>>>>>>>> merely amplify
>>>>>>>> them.
>>>>>>>> To me this seemingly minor difference is huge. If amps only
>>>>>>>> amplify but
>>>>>>>> do not generate harmonics then there is no scientific reason
>>>>>>>> for filtering
>>>>>>>> after the amp assuming the same amount of filtering is applied
>>>>>>>> before the
>>>>>>>> amp. In practical terms, this would mean that low power BPFs
>>>>>>>> before the amp
>>>>>>>> are as effective as high power BPFs after the amp.
>>>>>>>> The key point here is GENERATE vs AMPLIFY harmonics. Can the
>>>>>>>> average
>>>>>>>> commercial, well stabilized amp generate harmonics?
>>>>>>>> Rudy N2WQ
>>>>>>>> Sent using a tiny keyboard. Please excuse brevity, typos, or
>>>>>>>> inappropriate autocorrect.
>>>>>>>> On Jul 24, 2016, at 5:14 PM, Jukka Klemola
>>>>>>>> <jpklemola at gmail.com> wrote:
>>>>>>>>> In case you do that, you still need stubs after the amp.
>>>>>>>>> Amplifier creates harmonics out of the fundamental frequency.
>>>>>>>> _______________________________________________
>>>>>>>> CQ-Contest mailing list
>>>>>>>> CQ-Contest at contesting.com
>>>>>>>> http://lists.contesting.com/mailman/listinfo/cq-contest
>>>>>>> _______________________________________________
>>>>>>> CQ-Contest mailing list
>>>>>>> CQ-Contest at contesting.com
>>>>>>> http://lists.contesting.com/mailman/listinfo/cq-contest
>>>>>> _______________________________________________
>>>>>> CQ-Contest mailing list
>>>>>> CQ-Contest at contesting.com
>>>>>> http://lists.contesting.com/mailman/listinfo/cq-contest
>>>>
>>> _______________________________________________
>>> CQ-Contest mailing list
>>> CQ-Contest at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/cq-contest
>>>
>>>
>>>
>>
More information about the CQ-Contest
mailing list