[ct-user] CT 9.90.007 and Paddle

[Bob Schreibmaier]

Excellent suggestion!  Hate to admit it, but that
never even occurred to me.  Doh!

Radio turned off, all cables disconnected, same results.
CT will send a string of dits or string of dahs with
no problems.  Mix them up and garbage comes out,
after the first character.

----- Original Message -----
From: "Ed Parish K1EP" <k1ep at arrl.net>
To: "Bob Schreibmaier" <k3ph at ptd.net>; <k1ttt at arrl.net>
Cc: <ct-user at contesting.com>
Sent: Thursday, June 26, 2003 8:22 PM
Subject: Re: [ct-user] CT 9.90.007 and Paddle


> Don't even connect it to the radio to test.  Type SOUND to turn on the PC
speaker and you will get sidetone from the PC.  That way you can check out
your computer setup regardless of the radio.
>
> >Hi David,
> >
> >Thanks for the response.
> >
> >This is my first attempt.  Running 5 watts into a dummy load.
> >Wiring looks good.  Single dits and dahs work okay.  Putting
> >them together creates garbage, after the initial good first
> >letter.  Tried Super CMOS, Curtis A, and Curtis B modes with
> >no difference.  Tried two different paddles with no difference.
> >
> >Was thinking about performing an exorcism.  8^)
> >
> >73,
> >Bob
> >
> >----- Original Message -----
> >From: "David Robbins K1TTT" <k1ttt at arrl.net>
> >To: "reflector ct-user" <ct-user at contesting.com>
> >Sent: Thursday, June 26, 2003 4:20 PM
> >Subject: RE: [ct-user] CT 9.90.007 and Paddle
> >
> >
> >> Check that you aren't getting rf into the port... turn off or reduce
> >> radio power.  Doublecheck wiring and pin numbers, make sure no pins are
> >> shorted and that pullup resistors are properly connected.  Slow the
> >> speed way down and try to send single dits and dahs to see if maybe you
> >> have bounce in a paddle contact.  Has it worked with earlier versions
on
> >> that machine or is this your first attempt??
> >>
> >>
> >> David Robbins K1TTT
> >> e-mail: mailto:k1ttt at arrl.net
> >> web: http://www.k1ttt.net
> >> AR-Cluster node: 145.69MHz or telnet://dxc.k1ttt.net
> >>
> >>
> >> > -----Original Message-----
> >> > From: ct-user-bounces at contesting.com [mailto:ct-user-
> >> > bounces at contesting.com] On Behalf Of Bob Schreibmaier
> >> > Sent: Thursday, June 26, 2003 20:00
> >> > To: ct-user at contesting.com
> >> > Subject: [ct-user] CT 9.90.007 and Paddle
> >> >
> >> > I tried to use CT 9.90.007 and an external paddle on
> >> > a Toshiba 486/50 laptop (QRP Field Day computer)
> >> > running MS-DOS 6.22.  I used the REVPADDLE command
> >> > to get the left paddle to send dits and the right
> >> > to send dahs.
> >> >
> >> > Sending with the motion necessary to send a "V",
> >> > the first letter out is a "V", but the next one is an
> >> > "F", followed by something unintelligible.
> >> >
> >> > I've tried not using REVPADDLE, but simply changing
> >> > the paddle around.  Same results.
> >> >
> >> > Has anyone else seen this behavior?  Is it possible
> >> > to fix?
> >> >
> >> > TIA.
> >> >
> >> > 73,
> >> >     ____             /        _____           /
> >> >    /    )           /        /               /
> >> >   /____/   ____    /___     (____    ____   /___    /___
> >> >  /     )  /    )  /    )         )  /      /    )  /
> >> > /_____/  /____/  /____/    _____/  (____  /    /  /       . . .
> >> >
> >> > +---------------------------------------------------+
> >> > | Bob Schreibmaier K3PH | E-mail: k3ph at ptd.net      |
> >> > | Kresgeville, PA 18333 | http://home.ptd.net/~k3ph |
> >> > +---------------------------------------------------+
> >> >
> >> > _______________________________________________
> >> > CT-User mailing list
> >> > CT-User at contesting.com
> >> > http://lists.contesting.com/mailman/listinfo/ct-user
> >>
> >>
> >>
> >> _______________________________________________
> >> CT-User mailing list
> >> CT-User at contesting.com
> >> http://lists.contesting.com/mailman/listinfo/ct-user
> >>
> >
> >_______________________________________________
> >CT-User mailing list
> >CT-User at contesting.com
> >http://lists.contesting.com/mailman/listinfo/ct-user
>
>
> CONFIDENTIALITY NOTICE: This message is a PRIVATE communication. This
email may
> contain privileged and confidential information intended only for the
above-named
> recipient. If you have received this in error and you are not the intended
> recipient, you are hereby notified that any use, dissemination, or copying
is
> strictly prohibited. In such case, do not read, copy, or use it, and do
not disclose
> it to others. Please notify the sender of the delivery error by replying
to this
> message, and then delete it from your system. Thank you.
>
>
>
>