[TenTec] Omni 6+ Input vs Output power?
Steve Weber
kd9bo at mac.com
Wed Jan 7 00:07:49 EST 2004
The Delta II also reduces the drive automatically.
>Rick,
>
>With the Omni V, Paragon, Paragon II, Omni VI, Jupiter, and Orion, there is
>overcurrent protection built into the radio. The radio will automatically
>reduce its own drive to prevent the final current from going above a set
>threshold. The older Omni A and Omni D did not have this protection. Also
>the Pegasus does not have this over current protection.
>
>Carl Moreschi N4PY
>Franklinton, NC
>----- Original Message -----
>From: "Rick Westerman" <Rick at dj0ip.de>
>To: <tentec at contesting.com>
>Sent: Wednesday, January 07, 2004 12:42 AM
>Subject: RE: [TenTec] Omni 6+ Input vs Output power?
>
>
>> MIKE, BE CAREFUL
>>
>> Yes, the current consumption varies from band to band and when
>> limiting to 20A, you may not always get 100w out.
>>
>> However, the 962 is incorporated in the protection circuitry of
>> the Omni VI+ and has over-current shutdown (which I'm sure you
>> have already experienced). If you use a non-T-T P.S., you need
>> to insert an external automatic circuit breaker in the line.
>> These things typically come in values of 15A or 20A - dunno if
>> you can get one for 22A. Without this circuit breaker, you run a
>> HIGH RISK of blowing your final transistors. DON'T SAY WE DIDN'T
>> TELL YOU if you blow the things!
>>
>> I recommend returning to using the Model 962 and forget about the
>> missing 10 watts on some bands. It will never be noticed in any
>> QSO.
>>
>> 73
>> Rick
>>
>> -----Original Message-----
>> From: tentec-bounces at contesting.com
>> [mailto:tentec-bounces at contesting.com]On Behalf Of Barbara
>> Maloney
>> Sent: Wednesday, January 07, 2004 1:22 AM
>> To: ten tec list
>> Subject: [TenTec] Omni 6+ Input vs Output power?
>>
>> Is it common for the DC input amps, or Ic, to vary from 15 to 22+
>> to obtain 100 watts output into 50 ohms when changing bands?
>>
>> With my Omni 6, I was not able to get 100W output on 3 bands
>> before my former 962 supply would trip off at 20A. Have since
>> replaced it with a beefier more stable supply with an accurate dc
>> ammeter. The Ic scale runs approx. 1-2 A higher than the supply
>> dc.
>>
>> Has anyone had a problem running CW at over 20A DC input with the
>> Omni 6? The bands where the efficiency goes to pot (Idc exceeds
>> 20A for 100W rf out) are 160, 30, and 15. I know this agrees
>> with at least one other Omni 6 user. Any more?
>>
>> Thanks &
>> 73, Mike, AC5P
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
>_______________________________________________
>TenTec mailing list
>TenTec at contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec
--
Steve Weber
No trees were killed in the sending of this message. However
a large number of electrons were terribly inconvenienced.
*******************************
Hey spammers - Harvesting email addresses? Don't overlook these guys!
FCC Chairman Michael K. Powell: mpowell at fcc.gov
FCC Commissioner Kathleen Q. Abernathy: kabernat at fcc.gov
FCC Commissioner Michael J. Copps: mcopps at fcc.gov
FCC Commissioner Kevin J. Martin: kjmweb at fcc.gov
FCC Commissioner Jonathan S. Adelstein: jadelste at fcc.gov
US Postal Service: customer at email.usps.gov
Fraud Watch: fraudinfo at psinet.com
Federal Trade Commission: consumerline at ftc.gov
Federal Trade Commission: uce at ftc.gov
More information about the TenTec
mailing list