[TenTec] 425 titan

W1dxh at aol.com W1dxh at aol.com
Fri Jan 18 16:08:05 EST 2008


thank you all for the info on running rtty with the titan 425. hope to  print 
you all some time.
 
73's tnx,
steve  w1dxh
 
 
In a message dated 1/18/2008 12:27:27 P.M. Eastern Standard Time,  
sales at tentec.com writes:

Bob -- I  think you're quoting the specifications from the Titan II or 
Titan  III.

The Titan 425 is rated at 1000 watts continuous -- no time limit.  
Running RTTY with that amplifier at 1500 watts in usual digital mode  
duty cycle will not present a problem.   The maximum power  output for CW 
and SSB was well over 2000 watts -- it was designed with  lots of 
headroom.  The pair of 3CX800A's is rated 120 mA maximum grid  current; 
1500 watts out into a good load should run the amp in the 30-40  mA 
range, typically.

There were 3 Amateur Radio versions of the  Titan 425.  The easy way to 
tell them apart:  the first had a  dark case like the original Corsair, 
mid-1980's.  The second was a  grey case, Corsair II-style knobs and says 
TITAN 425 on the front  panel.  Serial numbered up to 425-01000.  Roughly 
1986 to  1989.  Third version has the rubberized knobs like the modern HF  
rigs, says TITAN on the front, serial numbers after 425-01000 and then  
date encoded serial numbers which we started using in 1989.    There 
technically was a fourth version -- the "Titan Gold" series, which  were 
the last 50 units built of the Titan.  They had a gold plate on  the 
front and a gold plastic logo.  They are the same as the third  version 
except they were the very last ones we sold when we announced we  were 
cutting it off and doing one final production run in  1996-97.

For the technical differences between the amps, I'd refer to  the service 
department.  I don't know them off the top of my  head.

There was also a military version of the Titan called the Titan  425D. 
Different power supply -- rack mount unit.  More broadbanded  coverage 
than the ham bands version, the front panel bandswitch labeling  is not 
15-20-40 etc. for the ham bands, but was labeled with frequency  
information like 3.3-5.7 MHz, etc.  Required less drive power than  the 
425.  Front panel, rear panel, and power supply also say Titan  425D. 
Interestingly enough, 15 years or so out of production not many of  these 
have turned up for ham radio use.  One can only wonder where  they all 
are now.

I bought a used 1989 vintage second version Titan  425 in 2001 and it has 
been run up to 20 contests a year since that  time.  Great amp.

73
Scott Robbins
W4PA

Bob McGraw -  K4TAX wrote:
> For RTTY it is rated 1000 watts output for 10 minutes of  transmit time 
with 
> a 50% duty cycle.  i.e. 10 minutes transmit,  followed by 10 minutes of 
> receive.  Follow the TUNE UP procedure  in the manual and do not over drive 
> the amp.  Pay very close  attention to Screen current and grid current.  Be 
> sure the  load/antenna is near 50 ohms i.e. SWR <1.5:1 before starting to 
>  tune the amp.  Start with 10 watts of drive from the exciter.
>  
>  While it is well protected, overdrive can make for expensive  and sudden 
> tube replacement needs.
> 
> And, if you don't  have a manual, order one from Tentec.
> 
> 73
> Bob,  K4TAX
>
_______________________________________________
TenTec  mailing  list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec





**************Start the year off right.  Easy ways to stay in shape.     
http://body.aol.com/fitness/winter-exercise?NCID=aolcmp00300000002489


More information about the TenTec mailing list