[TenTec] need help getting a Pegasus up and running

[Carl Moreschi]

Try my program.  You never know.  It defaults to the Pegasus for its 
configuration.  The only thing you have to set is the comport number.


Carl Moreschi N4PY
121 Little Bell Dr.
Hays, NC 28635
www.n4py.com

On 4/23/2011 9:19 PM, yash at aol.com wrote:
> Carl
>   thanks for the info. I was trying to ring out the Pegasus to make sure it basically worked ok.Iam using the same box I run with the 2 flex radios. It does not have a serial port. Iam using a usb to serial adpt I bought yesterday,no matter what data rates or com port settings the rig and software won't talk to each other. I don't see the problem going away by downloading your software,or is my thinking wrong?
>       There seems to be a hardware  software problem here. Would I be better off going to a PCI serial card ? I will down load your software tomarrow, and see what happens. Any suggestions on how to get the current setup to run. Man ,I feel like I did 6 years ago the first time I set up my old SDR-1000.
>    thanks for the help
> dale wt4t
>
>
>
>
>
>
>
>
>
>
> -----Original Message-----
> From: Carl Moreschi<n4py2 at earthlink.net>
> To: tentec at contesting.com
> Sent: Sat, Apr 23, 2011 8:07 pm
> Subject: Re: [TenTec] need help getting a Pegasus up and running
>
>
> First, you can download my N4PY sofwtare and run it on a 10 day free
>
> trial.  Just go to my website at www.n4py.com and then go to the Pegasus
>
> Downlaod page under the "More" Menu.  Download n4py319M.exe.
>
>
>
> The baud rate is fixed at 57600 and both the Tentec program and N4PY set
>
> this up.  The only setting you need to make is for the correct comport
>
> number.
>
>
>
>
>
> Carl Moreschi N4PY
>
> 121 Little Bell Dr.
>
> Hays, NC 28635
>
> www.n4py.com
>
>
>
> On 4/23/2011 7:06 PM, yash at aol.com wrote:
>
>>
>
>>
>
>>    Using the TT software from the TT down load site.  Computer is xp with sp-3
>
> and 4 gig of ram. Software loads fine on computer. Using a usb to serial
>
> cable,which on the device controller says its in place and working fine and is
>
> set on com 3. I went into the TT software and changed from com1 to com3 . turned
>
> on the Pegasus and started the software the two could not communicate with each
>
> other. tried all 6 different com port settings ,nothing changes. re loaded the
>
> TT software ,no change. What about the Baud rate and priority stuff,make a
>
> difference? could find no where the TT requirements for rates etc.
>
>>        I just got this Pegasus, was told it worked fine ...don't they all say
>
> that... I will buy the N4PY software as soon as I make sure the basic Pegasus is
>
> working ok. But need to get it up and on line with what I have.
>
>>
>
>> Maybe the usb/serial cable a bad thing??
>
>> can put a serial card in if needed .
>
>>
>
>> Sure would be grateful for any help on this. After using a flex 5000 and power
>
> sdr   for 4 years,thought the little Pegasus would be a no brainier.
>
>> Thanks
>
>> dale wt4t
>
>>
>
>>
>
>>
>
>>
>
>>
>
>>
>
>> _______________________________________________
>
>> TenTec mailing list
>
>> TenTec at contesting.com
>
>> http://lists.contesting.com/mailman/listinfo/tentec
>
>>
>
> _______________________________________________
>
> TenTec mailing list
>
> TenTec at contesting.com
>
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>