[TenTec] TenTec Digest, Vol 168, Issue 24

[Paul A. Ramey]

Barry,

If you have a drill press, I would use a reverse, left hand drill bit.


On 12/24/2016 11:00 AM, tentec-request at contesting.com wrote:
> Send TenTec mailing list submissions to
> 	tentec at contesting.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
> 	http://lists.contesting.com/mailman/listinfo/tentec
> or, via email, send a message with subject or body 'help' to
> 	tentec-request at contesting.com
>
> You can reach the person managing the list at
> 	tentec-owner at contesting.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of TenTec digest..."
>
>
> Today's Topics:
>
>     1. HELP with broken off screw threads (Barry N1EU)
>     2. Re: HELP with broken off screw threads (Peter Frenning [OZ1PIF])
>     3. HELP with broken off screw threads (Tom Hellem)
>     4. Re: HELP with broken off screw threads (Barry N1EU)
>     5. Re: HELP with broken off screw threads (Peter Frenning [OZ1PIF])
>     6. Re: HELP with broken off screw threads (Bryan Lee Cornwell)
>     7. Re: HELP with broken off screw threads (Mike Bryce)
>     8. Re: HELP with broken off screw threads (Barry N1EU)
>     9. SOLVED Re:  HELP with broken off screw threads (Barry N1EU)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Sat, 24 Dec 2016 15:02:05 +0000
> From: Barry N1EU <barry.n1eu at gmail.com>
> To: Discussion of Ten-Tec Equipment <tentec at contesting.com>
> Subject: [TenTec] HELP with broken off screw threads
> Message-ID:
> 	<CAFmfzDs=+mikAufBSFOPgj33cg=tLnbDK0A0i7X7GC8WjKo0Zg at mail.gmail.com>
> Content-Type: text/plain; charset=UTF-8
>
> The threaded end of an aluminum screw broke off in one of the PCB mounting
> posts in my Omni 6+.  Please have a look here:  http://n1eu.com/screw1.jpg
>
> I'd very much appreciate advice on how to remove that screw end.
>
> Thanks & 73,
> Barry N1EU
>
>
> ------------------------------
>
> Message: 2
> Date: Sat, 24 Dec 2016 16:06:59 +0100
> From: "Peter Frenning [OZ1PIF]" <peter at frenning.dk>
> To: Discussion of Ten-Tec Equipment <tentec at contesting.com>
> Subject: Re: [TenTec] HELP with broken off screw threads
> Message-ID: <66140d57-69b6-c3f1-0bdf-6c5c64c6a16c at frenning.dk>
> Content-Type: text/plain; charset=utf-8; format=flowed
>
> Den 24-12-2016 kl. 16:02 skrev Barry N1EU:
>> The threaded end of an aluminum screw broke off in one of the PCB mounting
>> posts in my Omni 6+.  Please have a look here:  http://n1eu.com/screw1.jpg
>>
>> I'd very much appreciate advice on how to remove that screw end.
>>
>> Thanks & 73,
>> Barry N1EU
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> Sorry Barry, I only get a partial picture...
>

-- 
Paul Ramey
WG0G
612-747-1244