[TenTec] TenTec Digest, Vol 168, Issue 24
Bwana Bob
wb2vuf at verizon.net
Mon Dec 26 18:11:10 EST 2016
If slotting the top doesn't work, file it off flat, drill out the screw
and re-tap the standoff.
Bob WB2VUF
On 12/24/2016 2:45 PM, Paul A. Ramey wrote:
> Barry,
>
> If you have a drill press, I would use a reverse, left hand drill bit.
>
>
> On 12/24/2016 11:00 AM, tentec-request at contesting.com wrote:
>> Send TenTec mailing list submissions to
>> tentec at contesting.com
>>
>> To subscribe or unsubscribe via the World Wide Web, visit
>> http://lists.contesting.com/mailman/listinfo/tentec
>> or, via email, send a message with subject or body 'help' to
>> tentec-request at contesting.com
>>
>> You can reach the person managing the list at
>> tentec-owner at contesting.com
>>
>> When replying, please edit your Subject line so it is more specific
>> than "Re: Contents of TenTec digest..."
>>
>>
>> Today's Topics:
>>
>> 1. HELP with broken off screw threads (Barry N1EU)
>> 2. Re: HELP with broken off screw threads (Peter Frenning [OZ1PIF])
>> 3. HELP with broken off screw threads (Tom Hellem)
>> 4. Re: HELP with broken off screw threads (Barry N1EU)
>> 5. Re: HELP with broken off screw threads (Peter Frenning [OZ1PIF])
>> 6. Re: HELP with broken off screw threads (Bryan Lee Cornwell)
>> 7. Re: HELP with broken off screw threads (Mike Bryce)
>> 8. Re: HELP with broken off screw threads (Barry N1EU)
>> 9. SOLVED Re: HELP with broken off screw threads (Barry N1EU)
>>
>>
>> ----------------------------------------------------------------------
>>
>> Message: 1
>> Date: Sat, 24 Dec 2016 15:02:05 +0000
>> From: Barry N1EU <barry.n1eu at gmail.com>
>> To: Discussion of Ten-Tec Equipment <tentec at contesting.com>
>> Subject: [TenTec] HELP with broken off screw threads
>> Message-ID:
>> <CAFmfzDs=+mikAufBSFOPgj33cg=tLnbDK0A0i7X7GC8WjKo0Zg at mail.gmail.com>
>> Content-Type: text/plain; charset=UTF-8
>>
>> The threaded end of an aluminum screw broke off in one of the PCB
>> mounting
>> posts in my Omni 6+. Please have a look here:
>> http://n1eu.com/screw1.jpg
>>
>> I'd very much appreciate advice on how to remove that screw end.
>>
>> Thanks & 73,
>> Barry N1EU
>>
>>
>> ------------------------------
>>
>> Message: 2
>> Date: Sat, 24 Dec 2016 16:06:59 +0100
>> From: "Peter Frenning [OZ1PIF]" <peter at frenning.dk>
>> To: Discussion of Ten-Tec Equipment <tentec at contesting.com>
>> Subject: Re: [TenTec] HELP with broken off screw threads
>> Message-ID: <66140d57-69b6-c3f1-0bdf-6c5c64c6a16c at frenning.dk>
>> Content-Type: text/plain; charset=utf-8; format=flowed
>>
>> Den 24-12-2016 kl. 16:02 skrev Barry N1EU:
>>> The threaded end of an aluminum screw broke off in one of the PCB
>>> mounting
>>> posts in my Omni 6+. Please have a look here:
>>> http://n1eu.com/screw1.jpg
>>>
>>> I'd very much appreciate advice on how to remove that screw end.
>>>
>>> Thanks & 73,
>>> Barry N1EU
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>> Sorry Barry, I only get a partial picture...
>>
>
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
More information about the TenTec
mailing list