[TenTec] Panadapter with 9MHz i.f.

[Greg S]

Thanks, Barry. The link on the wiki page points to wrong website for me. I understand it should go to the PAT50 i.f. Interface board designed for 12Mhz. Great, another project for the Omni VI+ when it gets on the bench! Merry Christmas to the TT family.Greg, KC8HXO

      From: Barry N1EU <barry.n1eu at gmail.com>
 To: Discussion of Ten-Tec Equipment <tentec at contesting.com> 
 Sent: Sunday, December 25, 2016 1:22 PM
 Subject: Re: [TenTec] Panadapter with 9MHz i.f.
   
I posted a Web page with all the panadapter info including photos of the
buffer amp mod in the Omni 6+:  http://omni6.wikidot.com/panadapt


73 & Happy Holidays,
Barry N1EU

On Sat, Dec 24, 2016 at 7:38 PM, Barry N1EU <barry.n1eu at gmail.com> wrote:

> Thanks Steve.  I'm finding that I can use 9.000MHz for i.f., cw offset is
> equal to (minus) sidetone frequency, USB offset is -3000Hz and LSB offset
> is zero.
>
> Yes, I'm using OmniRig to interface to the Omni 6+.
>
> HDSDR software has a neat "Mirror RF Spectrum in general" checkbox that
> makes the spectrum move correctly with the Omni 6/SDRPlay combo.  Back when
> I used an Orion/LP-Pan, I never saw the flipped spectrum issue.
>
>
>
> 73, Barry N1EU
>
> On Sat, Dec 24, 2016 at 7:21 PM, Steve Ellington <steven4lq at gmail.com>
> wrote:
>
>> Barry
>> I fiddled with this on a Corsair II. The offset for it was 750 Hz for cw
>> but on the O6 it would depend on your sidetone frequency setting. I would
>> guess 1500 Hz for SSB +/-.  I lost interest because it tuned backwards.
>> IOW.... tuning up the band caused the signals to move down. It's an (IF)
>> thing:*)
>> I would think OmniRig would be needed to interface the rig to SDR-C but I
>> used HDSDR. It can operate OmniRig which in turn operates most any rig via
>> serial port.
>> Let us know how it goes.
>> Steve N4LQ
>>
>> On Sat, Dec 24, 2016 at 1:48 PM, Barry N1EU <barry.n1eu at gmail.com> wrote:
>>
>> > Can anybody please provide the correct freq settings to use with
>> panadapter
>> > software being driven off the 9MHz i.f. output:
>> >
>> > IF OUTPUT 9.???.???  MHz
>> > Offsets  CW  ??? Hz
>> >            LSB ??? Hz
>> >            USB ??? Hz
>> >
>> > FWIW, I'm driving an SDRPlay RSP1 off my Omni 6+ 9MHz i.f. through a
>> > Clifton Labs Z10000B buffer amp.  I'm using SDR Console v3 software.
>> This
>> > looks like it's going to be a very cool setup.  I am fully documenting
>> the
>> > install.
>> >
>> > Thanks & 73,
>> > Barry N1EU
>> > _______________________________________________
>> > TenTec mailing list
>> > TenTec at contesting.com
>> > http://lists.contesting.com/mailman/listinfo/tentec
>> >
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
>
_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec