[TenTec] OMNI 6

[Bob McGraw]

Good morning Snowy.

The wife and I have both received our 2nd COVID vaccine.  We still take 
precautions when going out into public by always wearing a mask and 
using hand sanitizer as needed.  As my mother always said; "don't touch 
that, you don't know where its been".

Sounds as though the radio was likely used as a parts radio and what's 
offered is the carcass with a few parts still attached. Those old radios 
are good if they are working.  Otherwise, one needs to be creative to 
find and replace defective or missing parts.   Of course there are those 
folks that are collectors and are aficionados of Tentec radios.   I say 
better them than me.

Stay well and stay safe.

73

Bob, K4TAX


On 3/6/2021 3:45 AM, ROLAND HOWELL via TenTec wrote:
>
> Good Morning Bob, even if it is a cold one over here across the pond.
> Hope you and yours are staying clear of the pandemic.
> Thanks for your advice, just found out that there is NO case with it 
> either, so i am going to give it a miss.
> stay well and safe
> 73
> Snowy G0HZE
>
> ------ Original Message ------
> From: "Bob McGraw" <rmcgraw at blomand.net>
> To: tentec at contesting.com
> Sent: Saturday, 6 Mar, 21 At 01:45
> Subject: Re: [TenTec] OMNI 6
> As a rule, it is worth more in parts than a working radio. Frankly, I 
> wouldn't invest any time into repairs, even if it was given to me FOC.
> 73
> Bob, K4TAX
>
> On 3/5/2021 4:48 PM, Carlos PECO BERROCAL wrote:
> Hi,
> That sounds too hard for me.
> It is far from being complete, and these days getting parts has become 
> too
> difficult as most radio parts from ham estates go straight to the tip.
> If there was a healthy, reasonable market of second hand parts I would go
> for it. In your case I would focus into fixing the Paragons or asking 
> here
> for a complete, tech special Omni VI.
>
> 73,
> Carlos VK1EA
>
> On Saturday, March 6, 2021, ROLAND HOWELL via TenTec 
> <tentec at contesting.com>
> wrote:
> Good Evening gents
> looking at getting an incomplete OMNI 6 to play with.
> it requires the following pcb's:
> 81594 9mHz mixer board
> 81600 Pass Band Tuning board
> 81611 PA complete
> Just waiting on the seller to tell me if the top and bottom cases are 
> with
> it.
> My question to you gents is this, is anybody parting out that radio and
> have those boards for sale or disposal.
> Then once the radio is assembled will it work or will it require further
> work.
> What is the radio worth once all sorted, at the moments it is at £120.
> Its just for something to keep grey cell active during my retirement, 
> i am
> a sucker for TT kit having 3 x paragons ( only 2 working) Argosy2 x 2, a
> 509 Argonaut and finally 2 x Omni 'D's) ahh nearly forgot a 1254 Rx.
> So some thoughts from you gents please, worth doing or not!
> Stay well and healthy
> Snowy G0HZE .
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 
> <http://lists.contesting.com/mailman/listinfo/tentec>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 
> <http://lists.contesting.com/mailman/listinfo/tentec>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 
> <http://lists.contesting.com/mailman/listinfo/tentec>
>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec