[TowerTalk] ham4 into 25g??

[WA3GIN]

You can install a piece of steel angle with u-bolts in the same location as 
the rung you removed and not worry about it.

73,
dave
wa3gin
----- Original Message ----- 
From: "Bill Parry" <BPARRY at RGV.RR.COM>
To: <TOWERTALK at contesting.com>
Sent: Sunday, September 03, 2006 11:37 AM
Subject: Re: [TowerTalk] ham4 into 25g??


> When my tower went up in 2001 I knew that I was going to have to replace 
> the
> T2X from time to time. After fooling with putting the rotator into the 
> tower
> and talking to some guys that have done this same thing, I decided to cut 
> a
> rung at the location of the rotator. I also installed 2 thrust bearings
> instead of one, so that the bottom of the mast doesn't move around during
> the work. I am sure that cutting the rung in the tower compromises the
> strength of the tower but I haven't read or heard of this causing any
> serious problems and I know that it is done fairly often.
>
> I keep an extra rebuilt T2X in my attic for emergencies. I have had the 
> T2X
> replaced 2 times (not absolutely necessary) and the tower fellow does the
> work alone and "in no time".
>
> You might want to be sure and plan how you are going to replace your 
> rotator
> while the tower is on the ground rather than figure it out when it is up 
> in
> the air.
>
> Bill, W5VX
>
>
>>-----Original Message-----
>>From: towertalk-bounces at contesting.com [mailto:towertalk-
>>bounces at contesting.com] On Behalf Of Julio Peralta
>>Sent: Sunday, September 03, 2006 8:08 AM
>>To: 'Clint Talmadge'; TOWERTALK at contesting.com
>>Subject: Re: [TowerTalk] ham4 into 25g??
>>
>>Be very careful about mounting a rotor between 2 straight sections if
>>you have a problem with the rotor you will have to remove the antennas
>>and mast to disassemble the tower to remove the rotor for service or cut
>>a rung.
>>
>>Julio, W4HY
>>
>>-----Original Message-----
>>From: towertalk-bounces at contesting.com
>>[mailto:towertalk-bounces at contesting.com] On Behalf Of Clint Talmadge
>>Sent: Saturday, September 02, 2006 6:47 PM
>>To: Steve Litwins; TowerTalk at contesting.com
>>Subject: Re: [TowerTalk] ham4 into 25g??
>>
>>
>>I don't think it will fit without cutting a brace, which you do not want
>>to
>>do. However, I am curious why you would want to have all that mast down
>>in
>>the tower where it will twist in the wind.  If the mast is overly long,
>>let
>>it stick out the top and mount the antennas low on it, just over the
>>tower.
>>I saw one installation where the fellow had a 20' mast with about 6'
>>above
>>the bearing.  A Sommer antenna with about a 16' boom would wind that
>>mast up
>>and we would watch the end of boom move in a 45 degree swing, back and
>>forth
>>till the oscillations died down.
>>
>>my 2 cents and worth every penny you paid for it. ;^)
>>Clint - W5CPT
>>
>>----- Original Message -----
>>From: "Steve Litwins" <litwins2 at cox.net>
>>To: <TowerTalk at contesting.com>
>>Sent: Saturday, September 02, 2006 5:11 PM
>>Subject: [TowerTalk] ham4 into 25g??
>>
>>
>>> TT-ers...is it possible to get a Ham IV into a 25g down in the
>>> bracing?  I wud like to mount the rotor abt 1/2 way dn in the top
>>> section, but it does not seem to fit in through the bracing (too fat).
>>
>>> Anybody worked out this puzzle?  73/dx steve, k8wk
>>> **********
>>>
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>>
>>
>>_______________________________________________
>>
>>
>>
>>_______________________________________________
>>TowerTalk mailing list
>>TowerTalk at contesting.com
>>http://lists.contesting.com/mailman/listinfo/towertalk
>>
>>
>>_______________________________________________
>>
>>
>>
>>_______________________________________________
>>TowerTalk mailing list
>>TowerTalk at contesting.com
>>http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk