[TowerTalk] Gin pole
Roger (K8RI)
K8RI-on-TowerTalk at tm.net
Thu Dec 17 15:11:05 PST 2009
Tek Supp wrote:
> I bought my pullies (bottom and top) and the clamps from this guy and although they are home made, they work fine so far - I've used them about 5 times and I'm pleased, but I reserve to the right to complain in the future ;-). But for the tubing I went to a local shop called "Affiliated Metals" (801) 363-1711. A 20' 6061 T6 (2" OD x .125W 1.750 ID x 240") with tax was 48.08 this summer. It's in SLC, UT and I have no idea about shipping. But perhaps you can call them and find out. I then cut it down to 14' so I could have enough spacing/supported area for the tower clamps to the gin pole, but I didn't feel I needed the full 20'. I can't say that this helped you, but it's at least another avenue to pursue.
>
>
>
I use 20' of 1 1/2" galvanized steel fence tubing. with a 16" swivel
arm at the top so it can lower masting or tower sections in line with
the tower. It lifts 45G sections with no noticeable flexing. OTOH if
there is some side force it will spring without bending. I've lifted
well over 150# with it with very little deflection. I use a pulley on
top, the lifting pulley is floating on the rope, and the end of the rope
ties off at the end of the offset arm making heavy lifts relatively easy.
The only drawback of an all steel gin pole? The thing is "heavy"!.
I understand the quality of this material may vary. The place where I
get it (only about a 4 mile drive) has always had suitable material.
73
Roger (K8RI)
> Also suggested by w9iix, I also decide to buy a 20' of 1/4 wall for heavier pulls. I haven't used it yet, but it was a lot more (and I can't find my invoice right now for the pricing). The .125 (1/8") wall can flex, so be aware of that if you are lifting anything heavy. I was dismantling a 25G top section with rotor and mast and it flexed/bent toward the load a good foot. But I can state that the 20' 1/4" wall is quite a bit heavier and you don't want to be playing around with it up on the tower much.
>
>
>
> Thanks
>
> John
>
> K7ALA
>
>
>
>
>
>
>
>
>> From: k2owr at comcast.net
>> To: towertalk at contesting.com
>> Date: Thu, 17 Dec 2009 16:34:03 -0500
>> Subject: [TowerTalk] Gin pole
>>
>> :::: Anyone know where I can get a suitable 2" OD .125 wall 6061 piece of aluminum tubing, 12' long to use for a gin pole?
>> It needs to be within 100 miles of Knoxville TN so I can pick it up.
>> I'm aware that w9iix.com sells one in two pieces so it can be shipped, but then he asks a ridiculous $200 for it, plus shipping.
>> I already know this can be had at various tubing supply places for about $65, but they want $125 to ship it anywhere.
>>
>> Any suggestions appreciated.
>>
>> BILL K2OWR
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk at contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>
> _________________________________________________________________
> Hotmail: Trusted email with powerful SPAM protection.
> http://clk.atdmt.com/GBL/go/177141665/direct/01/
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
More information about the TowerTalk
mailing list