[TowerTalk] Plugs G-800

[Larry K4AB]

Use this link:  ..
http://www.wimo.com/cgi-bin/verteiler.pl?url=yaesu-rotator_e.html

The plugs are EXACT Yaesu replacements for the control box and the rotor
unit.
And, they cost less, as well, and ship quickly.

73,
Larry K4AB




On Tue, Jan 26, 2010 at 10:05 PM, larryjspammenot at teleport.com <
larryj at teleport.com> wrote:

> I, too, need one of the plugs for my Yaesu G800DXA rotator (the rotor end,
> not the controller). When you order a plug for it, does it come with any
> kind of "boot" or other weatherproofing system to keep water out of the
> contacts? Or do you just have to apply lots of "Coax-Seal" or some other
> similar material all over it and hope for the best?
>
> LJ
>
>
> -----Original Message-----
> >From: Perry - K4PWO <k4pwo at comcast.net>
> >Sent: Jan 26, 2010 7:25 PM
> >To: "Tower and HF antenna construction topics." <towertalk at contesting.com
> >
> >Subject: Re: [TowerTalk] Plugs G-800
> >
> >R&L Electronics has the NJC-207-PF connectors for $20 each.
> >See... http://www.randl.com/cgi-local/cart/cart.cgi?cart=ai&ID=39808
> >
> >73 de Perry - K4PWO
> >
> >--------------------------------------------------
> >From: "Terrence R. Redding Ph.D." <terry at oltraining.com>
> >Sent: Tuesday, January 26, 2010 06:49 AM
> >To: <towertalk at contesting.com>
> >Subject: Re: [TowerTalk] Plugs G-800
> >
> >> Jim, thanks for the comment.
> >>
> >> Yes, the new rotor motors ship with the seven pin male connector on the
> >> motor.  The older motor has a larger six pin plug.
> >>
> >> I am looking for a source of both.  If none are known, then I will call
> >> Yaesu.
> >>
> >> Terry - W6LMJ
> >>
> >>
> >> On 1/26/10 1:58 AM, "towertalk-request at contesting.com"
> >> <towertalk-request at contesting.com> wrote:
> >>
> >>> On Tue, 26 Jan 2010 00:14:05 -0500, Terrence R. Redding Ph.D. wrote:
> >>>
> >>>> I am wondering if there is a source for the six pin and seven
> >>>> pin female connectors that attach at the rotor motor end of the
> >>>> rotor control cable?
> >>>
> >>> I'm looking at schematic in the Yaesu manual for the rotor I bought
> >>> new this summer. The part numbr for the connector attached to the
> >>> rotor is NJC-207-RW. The cable-mounted connector that mates with it
> >>> is NJC-207-PF. At the time, I looked at the connectors and decided
> >>> that they were Japanese parts, but I did not recognize a mfr.
> >>>
> >>> The same manual also includes schematics for the G-2800DXA. The
> >>> corresponding connectors for that rotor are designated NJW-207-RW
> >>> and NJW-207-PF. I've not seen a G-2800DXA, so don't know the
> >>> difference between the connectors.
> >>>
> >>> The connectors for both rotors are 7-pin connectors.
> >>>
> >>> 73,
> >>>
> >>> Jim K9YC
> >>
> >>
> >> _______________________________________________
> >>
> >>
> >>
> >> _______________________________________________
> >> TowerTalk mailing list
> >> TowerTalk at contesting.com
> >> http://lists.contesting.com/mailman/listinfo/towertalk
> >>
> >_______________________________________________
> >
> >
> >
> >_______________________________________________
> >TowerTalk mailing list
> >TowerTalk at contesting.com
> >http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>