[WriteLog] Rttyrite and P38

[Denis Campbell]

Thanks to  those that  responded.   Success   at last using my P38  with
Windows  XP.  I  downloaded  and installed UserPort setting the port
address  to   0x360-0x363.   I  then used the   Windows  XP compatibility
wizard and selected   Windows 98 for   writelog. Voila--it  runs   just fine
now.

Denis
AA0YX


Denis
AA0YX
PAX
----- Original Message -----
From: "Jon Harder" <jon@praxisworks.org>
To: "Denis Campbell" <aa0yx1@attbi.com>
Sent: Tuesday, December 24, 2002 22:56
Subject: Re: [WriteLog] Rttyrite and P38


> Denis,
>
> >> I downloaded and  installed DirectIO
>
> Your message refers to a problem getting DirectIO to work in RttyRite,
> whereas Wayne's earlier reply to you links to the UserPort information at
> the WriteLog web page. These are rather different drivers.
>
> Some folks who have had problems with DirectIO have found that UserPort
> works just fine.  If you haven't actually tried it, I'd sure suggest
giving
> it a go.  When DirectIO failed to recognize my LPT ports under XP, I went
> with UserPort and it has worked perfectly ever since.
>
> 73,
>
> Jon     K1US
>
>
>
> ----- Original Message -----
> From: "Denis Campbell" <aa0yx1@attbi.com>
> To: <writelog@contesting.com>
> Sent: Tuesday, December 24, 2002 10:26 PM
> Subject: Re: [WriteLog] Rttyrite and P38
>
>
> > I downloaded and   installed DirectIO and it allows my P38  to  work in
> > everything but Rttyrite.   It   works just fine  in XPWare etc.
> >
> > Don't know why rttyrite won't  connect with DirectIO  and  everything
else
> > will.
> >
> > Denis
> > AA0YX
> >
> > ----- Original Message -----
> > From: "Wayne Wright, W5XD" <w5xd@writelog.com>
> > To: <aa0yx1@attbi.com>
> > Cc: <writelog@contesting.com>
> > Sent: Monday, December 23, 2002 20:23
> > Subject: Re: [WriteLog] Rttyrite and P38
> >
> >
> > > > I've just  installed Windows XP  and I'm trying to get my HAL P38
> > > > running without  success.  I've put  P38_PORT=OX360   into the
> > > > writelog.ini  file  in the  rttyrite section and still no joy.
> Anybody
> > > > have any  ideas.   I'm using  Writelog  10.37.
> > > >
> > > > Denis
> > > > AA0YX
> > > >
> > >
> > > The P-38 is not supported by WriteLog on Windows XP.
> > > However, you might be able to make it work. I haven't
> > > tried this, but if you look at the instructions here:
> > >
> > > http://www.writelog.com/support/lpt_port_support_on_windows_nt.htm
> > >
> > > You might be able to translate the directions to
> > > add the P-38 port addresses to the list allowed by
> > > UserPort.
> > >
> > > Off the top of my head, I don't remember exactly how many
> > > port addresses the P-38 uses, but it won't cause any extra
> > > damage to "open up" a wider range that it actually uses.
> > > You might try 0x350 through 0x370 to start.
> > >
> > > Wayne
> > >
> > >
> > > _______________________________________________
> > > WriteLog mailing list
> > > WriteLog@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/writelog
> > >
> >
> >
> > _______________________________________________
> > WriteLog mailing list
> > WriteLog@contesting.com
> > http://lists.contesting.com/mailman/listinfo/writelog
> >
>
>
>