[WriteLog] WriteLog & Microkeyer II

[Joe Wilkowski]

Update.  I removed WL 11.18 and did a full install of WL 11.12 and ran 
the application.  I  reset the WL Sound Control Mixer and WL comes up 
now with no "Error setting up device names for sound, Vista-Style" but 
after WL launches (approx 30 sec or so after program start) it still 
spawns the error message "Cant open sound card (3)".  But everything 
works as normal.  Sound works .

I then loaded WL 11.15A and still get the "Cant open sound card (3)" 
error but not the "Vista-Style" error.  I am going to stop while I am 
ahead.  The "Cant open sound card (3)" seems to be some artifact and it 
appears to be harmless.   Time will tell.  I have it working and I will 
leave it that way.


On 1/3/2014 9:58 PM, Steve Dyer wrote:
> I just started seeing this error as well, but everything is working 
> fine. Writelog 11.18 and MK2R+.
> 73,
> Steve
> W1SRD
>
>
> ------------------------------------------------------------------------
> *From:* Joe Wilkowski <k8fc at k8fc.com>
> *To:* writelog at contesting.com
> *Sent:*
> *Subject:* [WriteLog] WriteLog & Microkeyer II
>
> I run my station remote.  I just upgraded to 11.18 and now all I get is
> "Error setting up device names for sound, Vista-Style"  I know what this
> error means and I know that the sound devices do not appear to Writelog
> in the same order as the last time it was started.  I have encountered
> and fixed the issue before.  I know all that but, and a big but, No
> matter what I do with the PC and the WRITELOG.INI file I still get the
> error when launching WriteLog application.
>
> Steps I have taken.
>
> 1. Eliminated all sound card references in c:/windows/WRITELOG.INI file.
> (over and over again)
> 2. I have run the  WriteLog Sound Board Mixer Control application and
> selected the proper Codecs IE: xmit from PC = Headset Earphone
> (4-microHAM CODEC) DVK mic=Headset Microphone (4-microHAM CODEC) and rec
> to PC=Line(4-microHAM CODEC).  (over and over again)
> 3.  Eliminated all other Audio Codecs in the system .  The MicroHAM
> Codec is the only audio device available to any application. Same result.
>
> There is some Writelog glue that is not apparent.  When I open Writelog
> with NO codecs selected in the Writelog.INI file I do NOT get the error
> message
> "Error setting up device names for sound, Vista-Style" which is right,
> there are none selected.  BUT in all cases , including when I have
> codecs selected,  after the program starts  I get another error message
> saying "Cant open sound card (3)"  This indicates to me that Writelog is
> still trying to open a sound card that is in a different position but,
> there are none.  Only the MicroHAM codec.  There are NO other
> Writelog.ini files on that machine.
>
> I have re-installed WL (but not a full up installation) but I am 1500
> miles from the host PC.  I can do most anything to the PC except unplug
> the Microkeyer II, that  I cannot do.
>
> Any ideas ?  Anyone seen this before ?
>
> Thanks in advance,
>
> Joe K8FC
> _______________________________________________
> WriteLog mailing list
> WriteLog at contesting.com <mailto:WriteLog at contesting.com>
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
>