[WriteLog] MK2R+ and Writelog 11.18c

Joe Subich, W4TV lists at subich.com
Tue May 20 11:05:37 EDT 2014


Follow the manuals and make sure you have configured audio settings
correctly.

73,

    ... Joe, W4TV


On 2014-05-20 9:47 AM, post at lb3re.com wrote:
> I just saw Radio 2 MMTTY RX window was silent when I toggle between RAdio
> 1 and 2.
>
> I followed the Writelog setup.
>
> So something must be totally wrong????
>
> 73 LB3RE
>
>
> Den tir, mai 20, 2014, 15:37 skrev Joe Subich, W4TV:
>>
>> The example configuration is full of screen shots.
>>
>> 73,
>>
>>      ... Joe, W4TV
>>
>>
>> On 2014-05-20 9:24 AM, LB3RE LJ3RE Stein-Roar Brobakken wrote:
>>> If anyone can do printscreen of SO2r RTTY settings for MK2R+ in writelog
>>> and urouter soundcard + mmtty I had been very happy I was little
>>> confused by trying get it work too
>>>
>>> ---Sent by iphoneLB3RE LJ3RE K3RAG ex: LA6FJAwww.lb3re.com ~ Rag ~ Stein
>>> Roar Brobakken e-mail:post at lb3re.com
>>>
>>> On 20. mai 2014 13:10:19 CEST, Richard Thorne <rthorne at rthorne.net>
>>> wrote:         Group,  Thanks to Dean, Joe and Steve (GW4BLE) I
>>> determined that I had to go into the windows sound system and select the
>>> 2 channel option as described below.  Both instances of MMTTY are now
>>> receiving the proper signal and demodulating correctly.  Now on to the
>>> transmit issue which I'll tackle this evening.  I have a sneaking
>>> suspicion that it has to do with the way I have my com ports setup.
>>> I'll report back when I get it resolved.  After I get all of this
>>> working, I'll look at installing OCX  Thanks  Rich - N5ZC     On
>>> 5/19/2014 8:49 AM, Dean St. Hill wrote:   Rich    Welcome to the
>>> twilight zone. Been there. Many times.     To see the way the sound
>>> cards are set-up within your system - click on the Audio-switching tab
>>> of MK2R+. then click on "soundcard" - over on the right 2/3 down the
>>> window.     Even though the MMTTY plugin works, I would suggest that it
>>> might be a good idea to actually use t
>> he "OCX" set-up guideline as this is a more modern driver with the
>> possibility of also using "2tone" as an alternative to MMTTY.     if
>> you're setting audio from the left channel in both windows - 1st make sure
>> the buttons on MK2R+ are set correctly. That's the top right section of
>> MK2R. If that is correct then you need to go to windows sound system -
>> right click on the "speaker logo" in the system tray. Choose recording
>> devices. in the recording devices double-click the USB codec. Then choose
>> "advanced" tab - extreme right top of the new window.  You will then see a
>> drop-down with "default format" - this is where you need to choose a
>> stereo option. Your current default is probably a mono option.     I
>> choose 2 channel, 16 bit 44100Hz (CD Quality) and this has always worked
>> for me but I am almost sure it can be a much much lower quality - others
>> with more expertise may jump in and help with guidance here.     Finally
>> after clicking the necessary "OK" etc. return to the two MMTTY wind
>> ows and just confirm that left channel has been set up for your radio 1
>> and right channel for your radio 2.      Hmmm... you may also want to go
>> back to router as well and under audio switching tab re-confirm that the
>> "use line out channel" has also been set for radio one and radio 2. both
>> may be set as "left".     you should now be good to go as far as dual
>> receive.     let's get that going and then check the tx side of the
>> equation.     73 and best regards,      Dean - 8P6SH                On
>> Mon, May 19, 2014 at 7:37 AM, Richard Thorne <rthorne at rthorne.net>
>> wrote:This is a cross post to Writelog and Microham.  I've been working on
>> configuring an MK2R+ SO2R controller with a pair of K3's and my Win 7 Pro
>> computer.  I've been able to get SSB and CW to work properly.  I'm hung up
>> on RTTY using MMTTY.  I've downloaded the setup guide from Microham and
>> have setup two directories and two instances of MMTTY, I also have the
>> MMTTY plug in for Writelog installed.  If I select the test butt
>> on for FSK on the MK2R+ ports tab for rig 1 I get diddling same goes for
>> rig 2.  While in Writelog I've followed the setup instructions by first
>> selecting rig 1 and starting MMTTY from the appropriate directory, same
>> for rig 2.  However, I can't get either to diddle.  In addition, both
>> instances of MMTTY appear to be getting the same audio from rig 1 from the
>> phone jack.  I've selected the right and left audio source on the misc tab
>> while in TNC setup.  On the sound card tab in TNC setup I've selected
>> Reception: Microphone (3 - USB Audio CODEC) and Transmission: Speakers (3
>> - USB Audio CODEC)  How does one determine which device identifier to
>> select on the misc tab in tnc setup?  I thought it would be 3 but I'm
>> obviously incorrect.  I want to to use the line out on the rear of the
>> K3's to grab the audio since it's fixed and won't be affected by the
>> volume control of either K3.  The frustrating part is that I had this
>> MK2R+ working just fine on RTTY with one K3, adding the 2nd K3 has
>> been a challenge.  Is there an updated setup guide specifically for Win 7?
>>   I'm half tempted to dust off an XP Pro laptop and give that a try, Win 7
>> makes things very challenging.  Thanks in advance for any assistance.
>> Rich - N5ZC      _______________________________________________ WriteLog
>> mailing list WriteLog at contesting.com
>> http://lists.contesting.com/mailman/listinfo/writelog WriteLog on the web:
>>   http://www.writelog.com/          --  Dean St.Hill      Counterpoint
>> Consulting    17 Ocean City   St.Philip   Barbados       246-266-8230
>> 246-416-5277       dmsthill at gmail.com                 __._,_.___    Posted
>> by: Richard Thorne <rthorne at rthorne.net>        Reply via web post   •
>> Reply to sender    •    Reply to group    •   Start a New Topic   •
>> Messages in this topic (1)              This list is for the exchange of
>> information about the use and operation of microHAM products.    Anyone
>> with specific hardware support issues should contact microHAM support at
>> mailto:suppor
>> t at microHAM.com.       Visit Your Group   New Members 3          • Privacy
>> • Unsubscribe • Terms of Use             .       __,_._,___
>>> _______________________________________________
>>> WriteLog mailing list
>>> WriteLog at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/writelog
>>> WriteLog on the web:  http://www.writelog.com/
>>>
>> _______________________________________________
>> WriteLog mailing list
>> WriteLog at contesting.com
>> http://lists.contesting.com/mailman/listinfo/writelog
>> WriteLog on the web:  http://www.writelog.com/
>>
>
>
>


More information about the WriteLog mailing list