[Yaesu] Yaesu and related items FS

[Ken Simpson, W8EK]

Yaesu and related Items For Sale:

VX-7 Accessories, several Microphones,
Wattmeters, Communications Speakers,
HT accessories, and more


Yaesu VX-7 accessories:

VX-7 Nifty Mini Manual
A pocket reference to all of those commands that no one
remembers! For the VX-7.  Spiral bound.  $18

Programming cable
This cable has the threaded connector as used by the VX-7,
but it can also be used on the VX-6, 5, 3, etc.  Uses USB port.
It works great with the free "Chirp" program.  I have not
tried it with others. $18


Yaesu YD-148 Dual Impedance Desk Microphone:

The Yaesu YD-148 is a very nice "goose neck" type desk microphone.
It has both high and low impedances, which can be selected by a
switch. This means it can be used on some of the older rigs
requiring a high impedance mic, or with the more modern rigs
needing a low impedance mic.

This particular mic has had the mic element replaced with a
Heil HC-4 element, which is the "DX" element that Heil
designed for superior audio punch to get thru pileups.
These elements are no longer available, but are worth
$50 for just the element.

This particular mic is in very nice condition. It works 100%.
With round 8 pin connector for $85.


Yaesu MH-15 DTMF Touch Tone Microphone:
The MH-15 c6 is a hand microphone that features a 16 digit
DTMF Touch Tone Pad on the back, along with a lock/unlock
switch.  The top has up/down buttons.  Of course the PTT
is on the side.  This one has the round 6 pin connector.
It works fine and looks close to new.  $40


Yaesu YM-17 hand microphone:
The YM-17 is a hand microphone with up/down switches on
the top corner.  It has the round 6 pin connector.
This one works fine and looks really great.  $30


Yaesu YM-31 hand microphone:
The Yaesu YM-31 is a hand mic with a round 6 pin
connector. Apparently it is either similar or the
same as the MH-25A6j (not the MH-25 with the 8 pin
connector). It is a 600 ohm impedance hand microphone,
and has a Monitor on-off switch on the back.
It looks very similar to the Yaesu MH-1.
This one works fine and looks extremely nice. $25


MFJ 815 B Cross Needle Peak Reading HF Wattmeter:

The 815 B covers from 1.8 thru 54 MHz (160 thru 6 meters),
and features a cross needle display that reads forward
and reverse power simultaneously.  Of course this means
that SWR is displayed at the same time.  The scales
are 300/3000 Watt forward and 60/600 Watt reverse.
It will read peak or average power, selectable by a
switch. 12 V DC is needed for the lighted meter.

This particular unit works fine, and looks very
close to new.
With paper work for $65.


Daiwa CN-520 "Cross Needle" wattmeter:

This wattmeter covers 1.8 to 60 MHz, and is the "cross needle"
type, so it reads SWR at the same time it reads forward and
reflected power.

Forward scales of 2000 W or 200 W; reflected 400 W and 40 Watts.

This one looks very nice and works like new,
with the paperwork for $65.


Communications Speakers:

Realistic 21-549 A
This one is about 4 inches square but only about 2 inches
deep. It is rated for 5 watts, has an 8 ohm impedance, and
is listed as a 300 to 3000 Hz frequency response, making it
ideal for communications. 3.5 mm (1/8 inch) mono plug. It
is black in color, looks great, and sounds great. $18

Vanco SPB-5
Appears to be the same at above, but with a Vanco label.
Also includes gimbal mount. $15


Low Pass TVI Filters:

A low pass TVI filter is added to the transmitter to reduce
harmonic interference. All have SO-239 connectors, and are
50 ohm filters.

The first one works on 6 meters as well as HF:

Drake TV-5200-LP Low pass TVI filter
This is the filter that may also be used on the low end of six
meters, as well as HF. It is good for 1000 Watts "average" below
30MHz, and about 200 W up to 52 MHz. It is the newer version
of the TV-1000. $30

Bencher YA-1, high power, low pass TVI filter
If you need a heavy duty filter for the output of your amplifier,
this one is ideal. It will take full legal power plus, and has at
least 80 db signal attenuation at TV channel 2. This one works
great, and is in its original box.
Bencher currently sells these for about $90. Only $60.

Bencher YA-1
As above, not in original box. $45

B & W FL-10/1500
This filter cuts off just above 10 meters, and handles 1500
Watts. It is the latest model B&W filter.In very nice condition,
it looks close to new. $40

Johnson 250-20 Low Pass Filter
This is a 52 ohm cylindrical low pass filter with a cut
off frequency of 45 MHz and 75 db of attenuation.
It is rated to take 1000 Watts of AM, or 5000 Watts
PEP SSB. With mounting bracket. $30

Para Dynamics PDC 1089
This filter is rated at a full Kilowatt, up to 30 MHz.
5 x 6 x 2 inch black box, instead of the more familiar long
enclosure. It looks like new. $25


Yaesu HT Accessory Items:

Belt Clip for Yaesu FT-207, with hardware. $8

Wrist Strap for Yaesu FT-209, and others $4


Rubber Duck antennas for your HT:

All are for 2 meters, are in good condition,
and are $10 each, unless stated otherwise.

BNC - regular rubber duck

BNC - Original from Kenwood TH-215, about 5 inches long

5/16 inch threaded, as used by Motorola and others
Stubby - 4 inches long

Type F connector - 6.5 inches long

BNC Stubby for 440 MHz, 3 inches long


I also have many other accessories available such as many
different types of microphones, HTs, HF, VHF and UHF rigs, HF
and VHF/UHF antennas, and many miscellaneous accessories.
Just too many to list here. Please e-mail your requests.


Prices do not include shipping from Florida.

Thanks.

73,

Ken, W8EK

Ken Simpson
E-mail to W8EK at FLHam.net or W8EK at arrl.net
Voice Phone (352) 732-8400