Amps
[Top] [All Lists]

Re: [Amps] Is after-powerdown cooling desirable?

To: <jim.thom@telus.net>, <amps@contesting.com>
Subject: Re: [Amps] Is after-powerdown cooling desirable?
From: Charles Harpole <k4vud@hotmail.com>
Date: Tue, 20 Dec 2011 16:42:10 +0000
List-post: <amps@contesting.com">mailto:amps@contesting.com>
When I said, "It cant hurt anything"  My Father would say, "It cant do it any 
good."  Why not err on the side of caution and run the fan a few minutes after 
shut down?

Charles Harpole
k4vud@hotmail.com   
 > From: jim.thom@telus.net
> To: amps@contesting.com
> Date: Mon, 19 Dec 2011 21:25:48 -0800
> Subject: [Amps] Is after-powerdown cooling desirable?
> 
> Date: Sun, 18 Dec 2011 09:55:51 -0700
> From: "Jim  Garland" <4cx250b@muohio.edu>
> Subject: Re: [Amps] Is after-powerdown cooling desirable?
> 
> Roger K8RI says:
> " With external anode tubes and particularly the larger tubes we know that
> they continue to get hotter when the fan and power are killed at the
> same time."
> 
> I'm very surprised to hear this. Here's a counterargument: since the
> internal filament, cathode, and grid structures of an external anode tube
> dissipate very little heat, compared to the anode itself, I'd think that
> once the power is turned off, the anode would immediately begin to cool.
> Obviously it will cool more slowly if the blower turns off with the power,
> but I don't see why the anode temperature would ever increase after turnoff.
> 
> Further, since the anode is made of copper, there is a negligible
> temperature gradient between the inner and outer walls of the anode. While
> one can argue that it's nice to flush the heat out of the RF compartment
> after turnoff, that strikes me as a very modest benefit that doesn't warrant
> the complexity of a post-powerdown time delay circuit on the blower. 
> 
> The situation with glass tubes is different, since the internal anodes
> typically show color and run at a temperature much higher than the glass
> envelope. Thus, the heat will continue to radiate through the glass envelope
> for awhile after turnoff, and an airflow will keep the glass and seals cool
> during this time.
> 73,
> Jim W8ZR
> 
> ## It's the fil that keeps getting hotter, when the fil + blower are turned 
> off simultaneously.
> I did some air flow tests a while back on a hb  3CX-3000A7... with just fil + 
> blower running for
> 15 mins.  [ NO B+  and no drive].  I shut off the fil + blower at the same 
> time, then pulled the tube
> out, and had it sitting in my lap.    The coaxial fil stem [ both portions]  
> kept getting hotter and hotter
> and HOTTER.   My conclusion was/is... the heat in the fil was now migrating 
> out to the fil stem. 
> The anode is a non issue..provided you don't shut off the blower and fil, a 
> few secs after  running 
> full bore power. 
> 
> ## the Eimac notes say to use "blower over run"  on all these big metal, 
> external anode tubes, at least those
> with directly heated fils...and when done for the session, put amp into 
> standby, then shut off B+, then shut
> off the fil.  The blower is to stay on for  10-15 mins. 
> 
> ##  I ramp the fil v up..with a variac..and also ramp it  down when done for 
> the night.  A cam on the variac
> shaft + microswitch + relay ensure that the  varaic must be cranked fully CCW 
> in order to activate the
> microswitch + relay.  That way, if I forget to ramp it down from the night 
> before, I don't get a fil surge.  Fil won't 
> come on at all,  until the variac is 1st cranked  fully CCW.  After that, the 
> variac now has power, and can be used in
> the normal fashion.  A fluke 87 is used to measure the fil V...right at the 
> socket, via a pair of 200 uh chokes. 
> 
> ## the kenwood Tl-922 also had blower over run. 
> 
> later... Jim   VE7RF        
> 
> 
> 
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
                                          
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>