TenTec
[Top] [All Lists]

[TenTec] Semi-deaf Corsair II

To: <tentec@contesting.com>
Subject: [TenTec] Semi-deaf Corsair II
From: k6sdw@arrl.net (Eddy Avila)
Date: Mon, 30 Apr 2001 14:05:37 -0000
Jim, I agree with the others, Ten Tec stuff is prone to cold-solder joints, 
however usually the the bad joint can be isolated my bouncing and tapping 
the rig and circuit boards until its found.....my Corsair II had one in the 
High-IF board and drove me crazy until I pulled the board and and 
re-soldered every stinkin' connection and now finally fixed!

73......./k6sdw


>From: "Jim Reid" <kh7m@hsa-kauai.net>

>Hi to all,
>
>Well,  now am absolutely convinced my Corsair II is occasionally
>not hearing too well,  particularly low level CW signals
>are NOT heard/copied that are just fine on both the
>Triton 544 and Omni VI+!  The RF preamps in each of
>these rigs differ from one another.  I am going to assume
>that is the site of the problem as all else seems fine in
>the Corsair.
>
>In the Corsair II,  the RF preamp is Q3 on the RF Mixer board,
>#80987;  this is a simple transistor.  In the Triton,  the RF
>preamp is a dual gate MOSFET,  while in the Omni VI+, the
>RF preamp is a group of low NF grounded gate configured
>FETs.  Or,  the RF front ends are different in each of these
>TT rigs.
>
>Now,  my Corsair II was at TT back in August, '00 for a number
>of fixes,  PTO rebuild,  etc. -- the complete TT Service Dept.
>treatment!  A month after receiving it back out here in Hawaii,
>I had to return it again as the transmitter wouldn't transmit.
>The no charge fix that time was reordering the low level driver
>board connections,  reset the ALC,  and signed off as tested
>on all bands.
>
>I am sort of convinced that this radio, now some dozen or so years
>old,  is suffering from "old age" at least as far as traveling around
>via Fed Ex goes!  So am reluctant to return it once again to
>Tennessee,  as it was there only 7 months ago.
>
>All the CW beacons on 15 and 10 meters are easy to hear/copy
>today on both the Omni and Triton;  on the Corsair -- silence,
>only the hiss of noise.  Stronger CW signals can be heard,
>for example the K5 land beacon up at 28280,  and many SSB
>signals on 10 meters.  Other indicator about the Corsair is
>a very seldom moving S meter;  again an indicator,  I believe
>of only low level RF/IF signals getting to/through  the IF/AF
>board # 80984 on which the AGC and S meter circuitry lies.
>
>Another point, this "partial deafness"  seems to be there
>at one time,  and not at another.  For example,  when
>I started this note,  the "deafness" was in place.  After
>nearly finishing this note,  I have come back to the
>Corsair,  and it now seems to be hearing weak signals
>again!!
>
>I  suspect that the problem may not be the  RF amp transistor,
>Q3 on 80987,  but maybe a joint/connection which is
>"occasionally"  not good;  maybe temperature sensitive,
>or to a slight jiggle of the operating table (though this is
>pretty heavy and stable).  or......??  Assume this joint
>problem would be on, or near the 80987 board,  true?
>
>Even on a very,  very weak signal,  the signal to noise ratio
>still "hears" to be better on the Triton than when using the
>Corsair,  even in the apparent "good" state of operation.
>
>Too bad it is not a tube rig,  and I could just pull and
>change tubes,  hi.
>
>May have to call TT service dept. again,  phooey.
>
>73,  Jim,  KH7M
>
>
>--
>FAQ on WWW:               http://www.contesting.com/FAQ/tentec
>Submissions:              tentec@contesting.com
>Administrative requests:  tentec-REQUEST@contesting.com
>Problems:                 owner-tentec@contesting.com
>

_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com


--
FAQ on WWW:               http://www.contesting.com/FAQ/tentec
Submissions:              tentec@contesting.com
Administrative requests:  tentec-REQUEST@contesting.com
Problems:                 owner-tentec@contesting.com


<Prev in Thread] Current Thread [Next in Thread>