TenTec
[Top] [All Lists]

Re: [TenTec] Orion and SteppIR

To: <tentec@contesting.com>
Subject: Re: [TenTec] Orion and SteppIR
From: "Bernard(wtrone)" <wtrone@comcast.net>
Reply-to: tentec@contesting.com
Date: Sun, 11 Jul 2004 10:20:43 -0500
List-post: <mailto:tentec@contesting.com>
    Yes, my control box is the new one.  I received the antenna the end of
May.  The control box has the 57,600 baud setting and the Orion as a
transceiver option in the menu options.

    Matter of fact, I think that my shipment was partially delayed as they
worked out a solution for the Orion.  As I recall, it took them several
weeks to get a "loaner" Orion so that they could test the software.

    Thanks for your input.

        73,


        Bernard, WA4OEJ



----- Original Message ----- 
From: "Torrey Mitchell" <torreym@mchsi.com>
To: <tentec@contesting.com>
Sent: Sunday, July 11, 2004 9:45 AM
Subject: Re: [TenTec] Orion and SteppIR


> Bernard,
>
> My first question is...have you confirmed that your SteppIR box is a newer
> one with the mod for the Orion.  Back in February I was the first person
> apparently to discover that the Orion and the SteppIR box would not
> communicate.  I sent my box back to them for a month while they worked out
> a fix.  The problem was that the SteppIR box was never designed to
> communicate at 57,600 baud...the only comm freq for the Orion.  They came
> up with a new interface chip.
>
> It finally came home to my shack after this email from Jim at Fluidmotion:
> >Your controller should be there soon, we included a new cable that has
RTS
> >connected which according to one source at TEN-TEC is required. Set the
> >Controller to ORION with the BAUD= 57600. The Steppir controller will
> >Request the frequency from the Orion once every 2 seconds or so. When the
> >Steppir is set to General freq mode the Steppir should follow the Orion
> >frequency.
> >
> >If the Orion needs to be connected to the Computer you will need a "Y"
> >cable that connects the Computer or Radio's Pin-2 to the Steppir Data IN
> >Pin-2 (RXD) so it can monitor the data for the frequency information. It
> >should also be possible to connect the Steppir Pin-2 to the Computer
Pin-3
> >to read the set VFO command going to the Orion, this would be good for
> >trouble shooting.
> >
> >Hopefully it will just plug and go when you get your Orion back.
> >
> >Jim
>
> The last hurdle was the requirement for the cable to include an RTS
> connection.  It has worked fine since then.  You have to go through the
> menus on the box and select the Orion option.  If you don't see it, then
> you don't have an updated box.  I hate having to reprogram the box each
> time I switch between my Yaesu Mark V and the Orion, so I just use the
"ham
> mode" for one or the other.
>
> 73's and hamming,
> Torrey
> N9PY
>
>
> At 08:56 AM 7/11/2004, you wrote:
> >     After taking "care" of a few pine trees, I finally have my new 3
> > element SteppIR antenna up and operational.  It sure seems to work
> > well.  The antenna patterns seem to be a little sharper than the TH-7
and
> > A3WS that I was using.
> >
> >     I also bought the Orion to SteppIR interface unit, but can't seem to
> > get the interface to operate properly.  It seems like the two won't
> > communicate frequency information.  I talked to Fluid Motion on Friday
> > and they gave me the pin out information to make sure that the interface
> > cable was the correct one.  It checks out OK.  I've been through the set
> > up procedure about six times, step by step.  So, now, I am wondering if
> > it is operator error (of some type),  a problem with the Orion, or a
> > problem with the SteppIR control box.
> >
> >     Anyone on the board have an Orion with the SteppIR interface who
> > could shed a little light on the situation.  Is there a setting on the
> > Orion that I must activate?
> >
> >             73,
> >
> >
> >             Bernard, WA4OEJ
> >_______________________________________________
> >TenTec mailing list
> >TenTec@contesting.com
> >http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>