I haven't worked any AM yet with my O II, but I've listened a fair bit. I've
not heard any of the distortion spoken of so far. But I'm certain that the 6
kHz bandwidth limit imposed by th eroofing filter severely affects the audio
quality. There are no frequency components above 3 kHz hen using AM. Yet, if I
listen to the same signal in SSB with the BW set to 6 kHz, AM sounds better
than I've ever heard it. It seems that what we need for AM is a 12 kHz
bandwidth roofing filter and 12 kHz DSP bandwidth.
Kim Elmore, N5OP
----- Original Message ----
From: Ron Castro <ronc@sonic.net>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Sent: Wednesday, January 24, 2007 10:31:30 AM
Subject: Re: [TenTec] AM Receiver distortion in Orion II
The interesting thing about all of this is that on the Orion II AM stations
sound substantially better in SSB (same 3 kHz audio BW) than they do in AM!
I still think there is a DSP problem in the AM detector algorithm.
Ron N6IE
www.N6IE.com
(Formerly N6AHA)
----- Original Message -----
From: "Paul Christensen" <w9ac@arrl.net>
To: "Carl Moreschi" <n4py@arrl.net>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Wednesday, January 24, 2007 3:49 AM
Subject: Re: [TenTec] AM Receiver distortion in Orion II
>> Number 2, There is clearly a difference between the two recordings, so
>> maybe
>> someone in Tennessee has a tin ear?
>
> I just ran the two audio clips through SpectraPlus FFT software. The .MP3
> output is read directly by SpectraPlus internal to the sound card with no
> audio cabling necessary.
>
> The O2 has a sharp AM audio response cutoff at exactly 3 kHz (6 kHz of
> BW),
> as expected. On the FFT display, it is clearly a very sharp DSP cut-off
> with no detectable skirt. Audio response cuts off at 3 kHz and nothing
> escapes beyond that point. The O2 low-end response extends to below 80
> Hz,
> but rolls off smoothly below 90 Hz.
>
> On the TS-870, the AM response is also quite sharp, but cuts off at
> approximately 3.7 kHz. What we are all hearing is the significance of the
> speech intelligibility in the area between 3 and 4 kHz. That region does
> more to add speech intelligibility than any other area of the audible
> spectrum. This should come as no surprise when one looks at the
> Fletcher-Munson family of loudness curves. At approximately 3.5 kHz, the
> ear is most sensitive to absolute sound pressure level. Why? Because the
> ear canal terminates into the tympanic membrane and forms a closed
> acoustical pipe whose average resonant frequency is -- about 3.5 kHz. The
> exact point of resonance is a function of the length and diameter of our
> individual ear canals. So, a mere 700 Hz of added bandwidth makes a
> significant difference in intelligibility and is one reason why ESSB
> proponents have been advocating the use of extended-bandwidth SSB when
> conditions permit.
>
> Although things start sounding even better beyond 4 kHz, diminishing
> returns
> sets in quickly. In the interest of allowing operators the use of maximum
> speech intelligibility versus spectrum conservation, 4 kHz for SSB and 8
> kHz
> for AM is an excellent choice for maximum occupied bandwidth when
> operating
> conditions allow it.
>
> Paul, W9AC
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|