TenTec
[Top] [All Lists]

Re: [TenTec] OMNI6 PLUS Alignment procedure needed

To: <wb2vuf@arrl.net>,"Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] OMNI6 PLUS Alignment procedure needed
From: "John Cox" <jecox@tri-lakes.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 29 Dec 2007 10:03:41 -0600
List-post: <mailto:tentec@contesting.com>
I have an Omni 6 and an Omni 6+ and the manuals seem to be pretty detailed 
to me.  Most of the manual is devoted to descriptions of componets and 
service information.
What is it that I am missing here?  I would think that with the information 
supplied that any person with an electronics back ground could service them.

I would like to sell one of them.
The 6 has a 500 cycle filter in the 9 MC slot and option 1 installed. The 6+ 
has a 1.8 MC and 500 cycle filter in the 9 MC slots.
I want $1000 shipped to 48 states for the 6 or $1300 shipped to 48 states 
for the 6+
Both are in very good condition.  Being an amature amature radio operator I 
cant see any difference in their performance other than the extra filter in 
the 6+?
The 6 + had a power problem when I bought it and is recently back from 
Ten-tec where it had some pin diodes replaced and an alignment.

John Cox
KC0YAI
Bona, Missouri


----- Original Message ----- 
From: "Bwana Bob" <wb2vuf@gti.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Saturday, December 29, 2007 8:27 AM
Subject: Re: [TenTec] OMNI6 PLUS Alignment procedure needed


> It does take many hours to write and produce a service manual, but TT
> could sell them separately for those who want them. When I bought my
> Icom  R-71A, I bought the service manual too, and I'm very glad that I 
> did.
>
> I had no idea that Ten-Tec was no longer supplying servicing
> information. My Corsair, Paragon, and Scout all came with detailed
> manuals. This is what set Ten-Tec apart from the imports. Traditionally,
> Ten Tec encouraged owners to service their equipment, even making spare
> boards available. Not so with the imports. It will be a sad day when Ten
> Tec products can only be serviced at the factory.
>
> 73,
>
> Bob WB2VUF
>
> OTAKEBI@aol.com wrote:
>> I have been trying to get this type of information for my OMNI V for 
>> years
>> with no luck.
>> Ten Tec simply will not give it out.
>> This is kind of like what the Thorens turntable company did long  ago.
>> It was fine until the company was sold and the company included the 
>> dealers
>> in the non distribution of repair information.
>> Some of us kept copies of all the old technical information and shared 
>> the
>> information with others.
>> Eventually the company that bought Thorens went under and it is a good 
>> thing
>> we did what we did.
>> Every bit of technical information that we did not save went under  with 
>> the
>> company.
>> One day if that happens to Ten Tec and they are no longer around to 
>> repair
>> we will be in trouble.
>> I have long advocated that we get together and share with each other any
>> technical information we can get are hands on.
>> I was told by the top man at Ten Tec that the decision not to make 
>> service
>> manuals, after the Paragon, was a business decision to save the cost of 
>> making
>> service manuals.
>> That may have been a good thing for Ten Tec but not for owners.
>> I would like to know what the rest of you think about this problem.
>> Dan/N4VET
>>
>>
>>
>>
>>
>> **************************************See AOL's top rated recipes
>> (http://food.aol.com/top-rated-recipes?NCID=aoltop00030000000004)
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>