TenTec
[Top] [All Lists]

Re: [TenTec] Centurion and AM

To: <bcarling@cfl.rr.com>, "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Centurion and AM
From: "Bob McGraw - K4TAX" <RMcGraw@Blomand.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 1 Aug 2014 23:28:53 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Ever see a Continental AM Broadcast transmitter? In some of the models you will find the last stage to be a big linear amplifier. Of course those were used long ago when we weren't worried about heat or the electric bill.

Centurion inefficient??? It's output is about 1000 to 1200 watts PEP with an input of about 2300 watts. That's about 54% or so. The Omni VII runs about 40% efficient on SSB at 100 watts PEP. Even my 1 KW class C AM transmitter, being pair of 4-400's modulated by a pair of 4-400's will have a PA efficiency of about 65%.

Don't knock linear amplifiers in terms of efficiency. The secret to a clean AM signal is to use a linear amplifier that is indeed "linear". Proper tuning along with correct drive is the key to this success. The nay sayers of course will say otherwise.

Remember, it takes a bit of cherry color on the plates to burn the gas out of the envelope. It is actually good for the tubes.

73
Bob, K4TAX






----- Original Message ----- From: <bcarling@cfl.rr.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Friday, August 01, 2014 10:02 PM
Subject: Re: [TenTec] Centurion and AM


I tune my Centurion 422 with enough drive for 1 KW out.

Then I feed it about 20 - 25 watts of carrier and start modulating. Currently using the OMNI VII. DON'T overdrive it! Keep an eye on the plates and let them only glow a little. You don't
want them melting!  Your mileage may vary.

You will get lectured by the purists on how "terribly inefficient" this is, but if it works I don't
knock it!

Bry, AF4K

On 1 Aug 2014 at 20:59, Timothy Johnston wrote:

I would be feeding it with 25w of AM from a TS-590. So.. exactly what would
the safe procedure be?

73 de Tj, K4TFJ ...


On Fri, Aug 1, 2014 at 8:46 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:

> On Sat, Aug 2, 2014 at 12:28 AM, george fritkin via TenTec <
> tentec@contesting.com> wrote:
>
> > 200 to 250 watts AM results in 800 to 1000 watts PEP at 100% > > modulation.
> > Three 811 tubes can not handle that power.
> >
>
> How about two 3-500Z's?
>
> 73, Barry N1EU
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>