TenTec
[Top] [All Lists]

Re: [TenTec] Eagle 9MHz tap questions.

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Eagle 9MHz tap questions.
From: Carl Moreschi <n4py3@earthlink.net>
Reply-to: n4py3@earthlink.net, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 23 Dec 2014 09:01:34 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Yes, my software does all the syncing. And this connection is fully protected from transmit power.

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com

On 12/23/2014 8:52 AM, Rick - DJ0IP / NJ0IP wrote:
Oh, you mean just tap into the antenna line as it runs through the RX.
Now that's a piece of cake.

But that is effectively just feeding the TX antenna out to another RX.
How do you sync the ext radio to be on the same band as the Eagle?
I guess your software talks to both and takes care of that...?

73 - Rick, DJ0IP
(Nr. Frankfurt am Main)


-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Carl
Moreschi
Sent: Tuesday, December 23, 2014 1:52 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Eagle 9MHz tap questions.

Rick,

You can just put a Y connector between the two preselector jacks and run the
third leg to a panadapter radio such as the Softrock Ensemble II.
This works great.  My software will keep the softrock and Eagle on the same
frequency.

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com

On 12/23/2014 1:18 AM, Drago wrote:


-----Izvorna poruka----- From: Rick - DJ0IP / NJ0IP Sent: Tuesday,
December 23, 2014 5:32 AM To: 'Discussion of Ten-Tec Equipment' Subject:
Re: [TenTec] Eagle 9MHz tap questions.
I was wanting to add a pan-adapter.
I may have to replace a board in order to do that.
My unit does not have the TMP jack with the 9 MHz out.

Also I have to find a way to run the signal out the back.
I already have two spare RCA Phono jacks in use for the pre-selector.

73 - Rick, DJ0IP
(Nr. Frankfurt am Main)

-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
Richards
Sent: Tuesday, December 23, 2014 2:49 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Eagle 9MHz tap questions.

Are you going to add a panadapter ?

================== K8JHR ==================


On 12/22/2014 2:46 PM, Rick - DJ0IP / NJ0IP wrote:
Is it just a tap, like perhaps a Y-connection, or does it also have a
buffer stage?
Unfortunately my Eagle fell out of the nest before that feature was
added
to the radio.
____________________________________________
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>