TenTec
[Top] [All Lists]

Re: [TenTec] [TentecJupiter538] On cleaning connectors

To: "pw2501@yahoo.com" <pw2501@yahoo.com>, "TentecJupiter538@groups.io" <TentecJupiter538@groups.io>, "tentec@contesting.com" <tentec@contesting.com>, "TentecOmniVII@groups.io" <TentecOmniVII@groups.io>, "TenTecEagle@groups.io" <TenTecEagle@groups.io>, "TentecArgonautVI@groups.io" <TentecArgonautVI@groups.io>, "tentec-scout@groups.io" <tentec-scout@groups.io>
Subject: Re: [TenTec] [TentecJupiter538] On cleaning connectors
From: Bob McGraw K4TAX <rmcgraw@blomand.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Thu, 25 Jun 2020 11:55:42 -0500
List-post: <mailto:tentec@contesting.com>
Paul et al:

Thanks, I did not specify any details regarding "conditions" for a purpose.  Yes agreed, some conditions will accelerate oxidation.   In re-reading my post, it was not clear on the laws of chemistry and physics.  It should read "......has to do with the conditions......"

73

Bob, K4TAX


On 6/25/2020 11:36 AM, Paul Wojo wrote:
Beg to differ on some of that, Bob. Moist and high temperature environments will accelerate oxidation as will some environmental contaminants.

Best Regards.
Paul KE2AA

    On Thu, Jun 25, 2020 at 12:24, Bob McGraw - K4TAX
    <rmcgraw@blomand.net> wrote:
    Seems that I keep preaching this topic over and over and over. I
    recently addressed this issue on a Scout and a Century 22.

    Fact is, connectors oxidize.  It is the laws of chemistry and physics
    and has little to do with the conditions where the radio resided,
    past
    or present.  When connectors oxidize the electrical path is
    interrupted
    by the thin layer of oxidation.

    The solution is simple.   CLEAN ALL OF THE CONNECTORS.  Thus removing
    the oxidation and the radio returns to normal operation.    Just
    be sure
    to exercise the male connector on the female connector a couple of
    times
    and then be sure the connector is correctly and fully seated before
    moving on to the next connector.

    As to the cleaning process;  a Q-Tip with contact cleaner applied,
    {your
    choice of the magic chemistry} and then scrubbing the male pins is
    all
    that is necessary.    No hocus pocus, black magic, or voodoo act
    required.   And while you are in there.........DON'T screw with
    anything
    else.

    73

    Bob, K4TAX


    On 6/25/2020 10:57 AM, Josh Gibbs wrote:
    > Great advice from Bob. The Century 22 that I recently acquired
    had the
    > exact same symptoms: RX was good but no TX. Much of the problem
    turned out
    > to be due to a poor connection to the final amp board. I treated the
    > jumpers and connectors on the boards with Deoxit and suddenly
    had some
    > output!
    >
    > Good luck. The Scout is a great looking rig - I hope to add one
    to my small
    > Ten-Tec collection someday =)
    >
    > 73,
    >
    > -Josh WU7H
    >


    -=-=-=-=-=-=-=-=-=-=-=-
    Groups.io Links: You receive all messages sent to this group.

    View/Reply Online (#442):
    https://groups.io/g/TentecJupiter538/message/442
    Mute This Topic: https://groups.io/mt/75106476/2894444
    Group Owner: TentecJupiter538+owner@groups.io <mailto:owner@groups.io>
    Unsubscribe:
    https://groups.io/g/TentecJupiter538/leave/7510180/689371619/xyzzy
    <https://groups.io/g/TentecJupiter538/leave/7510180/689371619/xyzzy
    > [pw2501@yahoo.com <mailto:pw2501@yahoo.com>]
    -=-=-=-=-=-=-=-=-=-=-=-

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>