Towertalk
[Top] [All Lists]

Re: [TowerTalk] Crimper for Belden 9913 - Response DAVIS RF Co.

To: "Steve Davis -Davis RF Co." <sdavis@davisrf.com>
Subject: Re: [TowerTalk] Crimper for Belden 9913 - Response DAVIS RF Co.
From: Mark Spencer <mspencer12345@yahoo.ca>
Date: Tue, 6 Jan 2009 05:08:31 -0800 (PST)
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Sorry not sure what happened with the formatting here..  I'll try again..


Steve With regards to the center conductor expanding if it is cut after 
removing the dielectric, I have noticed this with 9913F7 as well.

Is there a special tool or technique that can be used to minmize this 
Best regards
Mark
VE7AFZ



________________________________
From: Mark Spencer <mspencer12345@yahoo.ca>
To: Steve Davis -Davis RF Co. <sdavis@davisrf.com>
Cc: towertalk@contesting.com
Sent: Tuesday, January 6, 2009 5:05:36 AM
Subject: Re: [TowerTalk] Crimper for Belden 9913 - Response DAVIS RF Co.

MIME-Version: 1.0
Content-Type: multipart/alternative; boundary="0-1296860631-1231247136=:69853"

--0-1296860631-1231247136=:69853
Content-Type: text/plain; charset=iso-8859-1
Content-Transfer-Encoding: quoted-printable

Steve:=0A=0AWith regards to the center conductor expanding if it is cut aft=
er removing the dielectric, I have noticed this with 9913F7 as well.=A0=A0=
=A0 Is there=A0special tool or technique that can be used to minmize this ?=
=0A=0ABest regards=0AMark=0AVE7AFZ=0A=0A=0A=0A=0A__________________________=
______=0AFrom: Steve Davis -Davis RF Co. <sdavis@davisrf.com>=0ATo: Roger (=
K8RI) <K8RI-on-TowerTalk@tm.net>=0ACc: mspencer12345@yahoo.ca; towertalk@co=
ntesting.com=0ASent: Monday, January 5, 2009 8:01:02 PM=0ASubject: Re: [Tow=
erTalk] Crimper for Belden 9913 - Response DAVIS RF Co.=0A=0A=0AHi Roger,=
=0A=0AThe ctr. cond. on LMR 400 (solid)=A0 and 400 UF (strnd'd)=A0 are both=
.108; however, cutting the ctr cond of the stranded=A0 400 UF=A0 , AFTER r=
emoving the dielectric will expand the OD....and sometimes dealing with the=
stranding anyway will cause it to expand a bit .=0A=A0 Ref. whether=A0 cri=
mp pins vs. clamp pins are different:=A0 for the most part they are differe=
nt, in the below around .500" OD cables; however, some mfrs. do have a few =
sizes and types that they are the same.=0A=A0 Ref. soldering crimp type pin=
s:=A0 in production modes, crimps are just crimped due to labor time/cost, =
but in less than production line app's,=A0 I , and many before me, recommen=
d a little added security (electrically and mechanically) by soldering the =
center pin of crimp types, after crimping.=0A=A0 As many other things, "a l=
ittle of everything is involved"... not cut and dry.=0ABottom line: for mos=
t ham use, crimp or clamp:=A0 both are very good mechanically, when done ri=
ght and not hard to do it right.=A0 =A0 Crimps are less aggravating and we =
have excellent tools to use at less than $ 40 for the tool, $ 23.50 for mul=
ti cable die, and this tool is one of few out there that will let you chang=
e the die.=A0 I've used the best commercial production tools and this one i=
s fine even for repeat production...ratchet release at proper torque on die=
, etc.=0A=A0 And Roger, you are a testimony to a "satisfied crimping ham"=
=A0 HI=0A=0A73,=A0 Steve ,=A0 K1PEK,=0A=0ADAVIS RF Co.,=A0 Div. of Orion Wi=
re Co., Inc.=0A=0AWire, Cable, RF Connectors and wire aerial parts.=A0 LMR,=
Heliax, Eupen=0A=0ACommercial / Military / & Custom Cable Design=0A=0Atel:=
=A0 978-369-1738=A0 =A0 Fax:=A0 978-369-3484=0Awww.DavisRF.com=0A=0A=0A=0A=
=0A----- Original Message ----- From: "Roger (K8RI)" <K8RI-on-TowerTalk@tm.=
net>=0ATo: "Steve Davis -Davis RF Co." <sdavis@davisrf.com>=0ACc: <towertal=
k@contesting.com>=0ASent: Monday, January 05, 2009 9:49 PM=0ASubject: Re: [=
TowerTalk] Crimper for Belden 9913 - Response DAVIS RF Co.=0A=0A=0A> =0A> A=
thought here:=A0 I think he's talking about the flexible version with the =
stranded center conductor which like the LMR-400UF is a bit larger than the=
solid center conductor.=A0 Although I've always been able to get them to f=
it into the standard center pins, it sometimes takes a bit of determination=
and care.<:-))=0A> =0A> I've also noted an inconsistency in the crimp, Vs =
Clamp descriptions.=A0 One supplier told me when I wanted crimp connectors =
with solder center pins they were either one of the other, not a mix, but I=
have a number of crimp connectors for LMR-600 that use center pins designe=
d for soldering complete with the small solder hole drilled in the side. OT=
OH even if the center pin is designed for crimping it can be soldered.=0A> =
=0A> Between the die sets I have for RG-8/LMR-400/9913/9913F I have both 0.=
100 and 0.128, plus the tiny ones meant for 8X and 58 type cables.=0A> =0A>=
Steve Davis -Davis RF Co. wrote:=0A>> Mark,=A0 One of my affiliates that d=
oes=0A>> cable assembly/terminations indicates that the .128 is not a good =
die to use, unless you tin the ctr conductor and find it to be a tight fit =
after crimping. They tinn and then solder the center pin on.=A0 Finding the=
.116 die and tool handle is possible but they don't know a source, other t=
han what Amphenol is recommending, quite expensive I'm sure.=A0 Given that =
you are not in "production" mode, taking the time to tin, crimp and solder =
is certainly a thorough way of obtaining a good electric/mechanical connect=
ion to either of these cables.=0A>>=A0 I think (?) that you had a follow-up=
question, or that was somebody else... I will find that again later and an=
swer it.=0A>> =0A>> =0A> One possibility for those who really insist on cri=
mping the center conductor is to take a 0.100 die and "adjusting" it with a=
small file to 0.116 which is only 0.016 larger...IE 16 thousandths of an i=
nch isn't much.=A0 OTOH they'd want to make sure the new=A0 die is properly=
marked, or identified.=0A> =0A> 73=0A> =0A> Roger (KI8RI)=0A> =0A> =0A>> 7=
3,=A0 Steve ,=A0 K1PEK,=0A>> =0A>> DAVIS RF Co.,=A0 Div. of Orion Wire Co.,=
Inc.=0A>> =0A>> Wire, Cable, RF Connectors and wire aerial parts.=A0 LMR, =
Heliax, Eupen=0A>> =0A>> Commercial / Military / & Custom Cable Design=0A>>=
=0A>> tel:=A0 978-369-1738=A0 =A0 Fax:=A0 978-369-3484=0A>> www.DavisRF.co=
m=0A>> =0A>> =0A>> =0A>> ----- Original Message ----- From: "Steve Davis -D=
avis RF Co." <sdavis@davisrf.com>=0A>> To: <towertalk@contesting.com>=0A>> =
Cc: <mspencer12345@yahoo.ca>=0A>> Sent: Sunday, January 04, 2009 1:26 AM=0A=
>> Subject: Crimper for Belden 9913 - Response DAVIS RF Co.=0A>> =0A>> =0A>=
> =0A>>> Mark,=A0 Ctr. conductor size for 9913 and 9913F7 is .108", so spec=
'g the .116 die makes sense.=A0 however, my crimper source indicates that t=
heir .128" is the one to use for 9913.=A0 This may not be as odd as it soun=
ds because the Belden spec can vary to +- .010, and I doubt it is on the mi=
nus side.=A0 At any rate, I am checking with a reliable source on Monday to=
see if the .128 will do the job well, I suspect so as my mfr. source for t=
he crimper and die is a very good one.=A0 Will advise on Mon.=0A>>> =0A>>> =
73,=A0 Steve ,=A0 K1PEK,=0A>>> =0A>>> DAVIS RF Co.,=A0 Div. of Orion Wire C=
o., Inc.=0A>>> =0A>>> Wire, Cable, RF Connectors and wire aerial parts.=A0 =
LMR, Heliax, Eupen=0A>>> =0A>>> Commercial / Military / & Custom Cable Desi=
gn=0A>>> =0A>>> tel:=A0 978-369-1738=A0 =A0 Fax:=A0 978-369-3484=0A>>> www.=
DavisRF.com=0A>>> =0A>>> =0A>>> =0A>>> Date: Sat, 3 Jan 2009 18:00:20 -0800=
(PST)=0A>>> From: Mark Spencer <mspencer12345@yahoo.ca>=0A>>> Subject: [To=
werTalk] Crimper for Belden 9913=0A>>> To: towertalk@contesting.com=0A>>> M=
essage-ID: <375680.81409.qm@web38802.mail.mud.yahoo.com>=0A>>> Content-Type=
: text/plain; charset=3Diso-8859=0A>>> =0A>>> =0A>>> =0A>>> =0A>>> =0A>>> =
=0A>>>> Sorry for a possibly off topic post, but I'm wondering if any one h=
as any wisdom crimping N connectors onto Belden 9913F7 that they could shar=
e with me.??=0A>>>> =0A>>>> According to the Amphenol web site http://www.a=
mphenolrf.com/pdf/283.pdf?the center pin for Amphenol 9913 conectors needs =
to be crimped with a .116 inch die.?? I've looked high and low for a .116 i=
nch die for my crimper and can't find one, I do have a .128 inch die and ac=
cording to the RF parts web site that is the appropiate size for crimping 9=
913 center pins.??? (The crimp for the outer connector seems to be?a common=
.429 inch size.)=0A>>>> =0A>>>> Google searches for .116 inch dies and cri=
mpers are not turning anything up either.=0A>>>> =0A>>>> I'm wondering if t=
he amphenol connectors need a different size crimper than other common conn=
ectors ???? I've always had good results using amphenol brand connectors an=
d would like to use them going forwards.=0A>>>> =0A>>>> I've seen several o=
ther crimpers advertised for crimping 9913 connectors but they don't specif=
y the die sizes.? I'm reluctant to order one with out knowing what the die =
sizes are.=0A>>>> =0A>>>> Does any one have any practical experience they c=
an share with me about crimping N connectors to Belden 9913F7 cable ??? I'd=
really like to use crimp style connectors going forwards but I want to mak=
e sure I crimp them properly.=0A>>>> =0A>>>> 73's=0A>>>> =0A>>>> Mark=0A>>>=
> VE7AFZ=0A>>>> =0A>>>> =0A>>>> =0A>>>> =0A>> =0A>> _______________________=
________________________=0A>> =0A>> =0A>> =0A>> ___________________________=
____________________=0A>> TowerTalk mailing list=0A>> TowerTalk@contesting.=
com=0A>> http://lists.contesting.com/mailman/listinfo/towertalk=0A>> =0A>> =
=0A> =0A> =0A=0A=0A      __________________________________________________=
________________=0ABe smarter than spam. See how smart SpamGuard is at givi=
ng junk email the boot with the All-new Yahoo! Mail.  Click on Options in M=
ail and switch to New Mail today or register for free at http://mail.yahoo.=
ca
--0-1296860631-1231247136=:69853
Content-Type: text/html; charset=us-ascii

<html><head><style type="text/css"><!-- DIV {margin:0px;} 
--></style></head><body><div style="font-family:times new roman, new york, 
times, serif;font-size:12pt"><DIV>Steve:</DIV>
<DIV>&nbsp;</DIV>
<DIV>With regards to the center conductor expanding if it is cut after removing 
the dielectric, I have noticed this with 9913F7 as well.&nbsp;&nbsp;&nbsp; Is 
there&nbsp;special tool or technique that can be used to minmize this ?</DIV>
<DIV>&nbsp;</DIV>
<DIV>Best regards</DIV>
<DIV>Mark</DIV>
<DIV>VE7AFZ<BR></DIV>
<DIV style="FONT-SIZE: 12pt; FONT-FAMILY: times new roman, new york, times, 
serif"><BR>
<DIV style="FONT-SIZE: 13px; FONT-FAMILY: arial, helvetica, sans-serif"><FONT 
face=Tahoma size=2>
<HR SIZE=1>
<B><SPAN style="FONT-WEIGHT: bold">From:</SPAN></B> Steve Davis -Davis RF Co. 
&lt;sdavis@davisrf.com&gt;<BR><B><SPAN style="FONT-WEIGHT: bold">To:</SPAN></B> 
Roger (K8RI) &lt;K8RI-on-TowerTalk@tm.net&gt;<BR><B><SPAN style="FONT-WEIGHT: 
bold">Cc:</SPAN></B> mspencer12345@yahoo.ca; 
towertalk@contesting.com<BR><B><SPAN style="FONT-WEIGHT: bold">Sent:</SPAN></B> 
Monday, January 5, 2009 8:01:02 PM<BR><B><SPAN style="FONT-WEIGHT: 
bold">Subject:</SPAN></B> Re: [TowerTalk] Crimper for Belden 9913 - Response 
DAVIS RF Co.<BR></FONT><BR><BR>Hi Roger,<BR><BR>The ctr. cond. on LMR 400 
(solid)&nbsp; and 400 UF (strnd'd)&nbsp; are both .108; however, cutting the 
ctr cond of the stranded&nbsp; 400 UF&nbsp; , AFTER removing the dielectric 
will expand the OD....and sometimes dealing with the stranding anyway will 
cause it to expand a bit .<BR>&nbsp; Ref. whether&nbsp; crimp pins vs. clamp 
pins are different:&nbsp; for the most part they are different, in the below 
around
.500" OD cables; however, some mfrs. do have a few sizes and types that they 
are the same.<BR>&nbsp; Ref. soldering crimp type pins:&nbsp; in production 
modes, crimps are just crimped due to labor time/cost, but in less than 
production line app's,&nbsp; I , and many before me, recommend a little added 
security (electrically and mechanically) by soldering the center pin of crimp 
types, after crimping.<BR>&nbsp; As many other things, "a little of everything 
is involved"... not cut and dry.<BR>Bottom line: for most ham use, crimp or 
clamp:&nbsp; both are very good mechanically, when done right and not hard to 
do it right.&nbsp; &nbsp; Crimps are less aggravating and we have excellent 
tools to use at less than $ 40 for the tool, $ 23.50 for multi cable die, and 
this tool is one of few out there that will let you change the die.&nbsp; I've 
used the best commercial production tools and this one is fine even for repeat 
production...ratchet release at proper
torque on die, etc.<BR>&nbsp; And Roger, you are a testimony to a "satisfied 
crimping ham"&nbsp; HI<BR><BR>73,&nbsp; Steve ,&nbsp; K1PEK,<BR><BR>DAVIS RF 
Co.,&nbsp; Div. of Orion Wire Co., Inc.<BR><BR>Wire, Cable, RF Connectors and 
wire aerial parts.&nbsp; LMR, Heliax, Eupen<BR><BR>Commercial / Military / & 
Custom Cable Design<BR><BR>tel:&nbsp; 978-369-1738&nbsp; &nbsp; Fax:&nbsp; 
978-369-3484<BR>www.DavisRF.com<BR><BR><BR><BR><BR>----- Original Message ----- 
From: "Roger (K8RI)" &lt;<A href="mailto:K8RI-on-TowerTalk@tm.net"; 
ymailto="mailto:K8RI-on-TowerTalk@tm.net";>K8RI-on-TowerTalk@tm.net</A>&gt;<BR>To:
 "Steve Davis -Davis RF Co." &lt;<A href="mailto:sdavis@davisrf.com"; 
ymailto="mailto:sdavis@davisrf.com";>sdavis@davisrf.com</A>&gt;<BR>Cc: &lt;<A 
href="mailto:towertalk@contesting.com"; 
ymailto="mailto:towertalk@contesting.com";>towertalk@contesting.com</A>&gt;<BR>Sent:
 Monday, January 05, 2009 9:49 PM<BR>Subject: Re: [TowerTalk] Crimper for Belden
9913 - Response DAVIS RF Co.<BR><BR><BR>&gt; <BR>&gt; A thought here:&nbsp; I 
think he's talking about the flexible version with the stranded center 
conductor which like the LMR-400UF is a bit larger than the solid center 
conductor.&nbsp; Although I've always been able to get them to fit into the 
standard center pins, it sometimes takes a bit of determination and 
care.&lt;:-))<BR>&gt; <BR>&gt; I've also noted an inconsistency in the crimp, 
Vs Clamp descriptions.&nbsp; One supplier told me when I wanted crimp 
connectors with solder center pins they were either one of the other, not a 
mix, but I have a number of crimp connectors for LMR-600 that use center pins 
designed for soldering complete with the small solder hole drilled in the side. 
OTOH even if the center pin is designed for crimping it can be 
soldered.<BR>&gt; <BR>&gt; Between the die sets I have for 
RG-8/LMR-400/9913/9913F I have both 0.100 and 0.128, plus the tiny ones meant 
for 8X and 58 type
cables.<BR>&gt; <BR>&gt; Steve Davis -Davis RF Co. wrote:<BR>&gt;&gt; 
Mark,&nbsp; One of my affiliates that does<BR>&gt;&gt; cable 
assembly/terminations indicates that the .128 is not a good die to use, unless 
you tin the ctr conductor and find it to be a tight fit after crimping. They 
tinn and then solder the center pin on.&nbsp; Finding the .116 die and tool 
handle is possible but they don't know a source, other than what Amphenol is 
recommending, quite expensive I'm sure.&nbsp; Given that you are not in 
"production" mode, taking the time to tin, crimp and solder is certainly a 
thorough way of obtaining a good electric/mechanical connection to either of 
these cables.<BR>&gt;&gt;&nbsp; I think (?) that you had a follow-up question, 
or that was somebody else... I will find that again later and answer 
it.<BR>&gt;&gt; <BR>&gt;&gt; <BR>&gt; One possibility for those who really 
insist on crimping the center conductor is to take a 0.100 die and "adjusting"
it with a small file to 0.116 which is only 0.016 larger...IE 16 thousandths of 
an inch isn't much.&nbsp; OTOH they'd want to make sure the new&nbsp; die is 
properly marked, or identified.<BR>&gt; <BR>&gt; 73<BR>&gt; <BR>&gt; Roger 
(KI8RI)<BR>&gt; <BR>&gt; <BR>&gt;&gt; 73,&nbsp; Steve ,&nbsp; 
K1PEK,<BR>&gt;&gt; <BR>&gt;&gt; DAVIS RF Co.,&nbsp; Div. of Orion Wire Co., 
Inc.<BR>&gt;&gt; <BR>&gt;&gt; Wire, Cable, RF Connectors and wire aerial 
parts.&nbsp; LMR, Heliax, Eupen<BR>&gt;&gt; <BR>&gt;&gt; Commercial / Military 
/ & Custom Cable Design<BR>&gt;&gt; <BR>&gt;&gt; tel:&nbsp; 978-369-1738&nbsp; 
&nbsp; Fax:&nbsp; 978-369-3484<BR>&gt;&gt; www.DavisRF.com<BR>&gt;&gt; 
<BR>&gt;&gt; <BR>&gt;&gt; <BR>&gt;&gt; ----- Original Message ----- From: 
"Steve Davis -Davis RF Co." &lt;<A href="mailto:sdavis@davisrf.com"; 
ymailto="mailto:sdavis@davisrf.com";>sdavis@davisrf.com</A>&gt;<BR>&gt;&gt; To: 
&lt;<A href="mailto:towertalk@contesting.com";
ymailto="mailto:towertalk@contesting.com";>towertalk@contesting.com</A>&gt;<BR>&gt;&gt;
 Cc: &lt;<A href="mailto:mspencer12345@yahoo.ca"; 
ymailto="mailto:mspencer12345@yahoo.ca";>mspencer12345@yahoo.ca</A>&gt;<BR>&gt;&gt;
 Sent: Sunday, January 04, 2009 1:26 AM<BR>&gt;&gt; Subject: Crimper for Belden 
9913 - Response DAVIS RF Co.<BR>&gt;&gt; <BR>&gt;&gt; <BR>&gt;&gt; 
<BR>&gt;&gt;&gt; Mark,&nbsp; Ctr. conductor size for 9913 and 9913F7 is .108", 
so spec'g the .116 die makes sense.&nbsp; however, my crimper source indicates 
that their .128" is the one to use for 9913.&nbsp; This may not be as odd as it 
sounds because the Belden spec can vary to +- .010, and I doubt it is on the 
minus side.&nbsp; At any rate, I am checking with a reliable source on Monday 
to see if the .128 will do the job well, I suspect so as my mfr. source for the 
crimper and die is a very good one.&nbsp; Will advise on Mon.<BR>&gt;&gt;&gt; 
<BR>&gt;&gt;&gt; 73,&nbsp; Steve ,&nbsp;
K1PEK,<BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; DAVIS RF Co.,&nbsp; Div. of Orion Wire 
Co., Inc.<BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; Wire, Cable, RF Connectors and wire 
aerial parts.&nbsp; LMR, Heliax, Eupen<BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; 
Commercial / Military / & Custom Cable Design<BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; 
tel:&nbsp; 978-369-1738&nbsp; &nbsp; Fax:&nbsp; 978-369-3484<BR>&gt;&gt;&gt; 
www.DavisRF.com<BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; 
<BR>&gt;&gt;&gt; Date: Sat, 3 Jan 2009 18:00:20 -0800 (PST)<BR>&gt;&gt;&gt; 
From: Mark Spencer &lt;<A href="mailto:mspencer12345@yahoo.ca"; 
ymailto="mailto:mspencer12345@yahoo.ca";>mspencer12345@yahoo.ca</A>&gt;<BR>&gt;&gt;&gt;
 Subject: [TowerTalk] Crimper for Belden 9913<BR>&gt;&gt;&gt; To: <A 
href="mailto:towertalk@contesting.com"; 
ymailto="mailto:towertalk@contesting.com";>towertalk@contesting.com</A><BR>&gt;&gt;&gt;
 Message-ID: &lt;<A href="375680.81409.qm@web38802.mail.mud.yahoo.com"">mailto:375680.81409.qm@web38802.mail.mud.yahoo.com";
ymailto="375680.81409.qm@web38802.mail.mud.yahoo.com"">mailto:375680.81409.qm@web38802.mail.mud.yahoo.com";>375680.81409.qm@web38802.mail.mud.yahoo.com</A>&gt;<BR>&gt;&gt;&gt;
 Content-Type: text/plain; charset=iso-8859<BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; 
<BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; <BR>&gt;&gt;&gt; 
<BR>&gt;&gt;&gt;&gt; Sorry for a possibly off topic post, but I'm wondering if 
any one has any wisdom crimping N connectors onto Belden 9913F7 that they could 
share with me.??<BR>&gt;&gt;&gt;&gt; <BR>&gt;&gt;&gt;&gt; According to the 
Amphenol web site <A href="http://www.amphenolrf.com/pdf/283.pdf?the";; 
target=_blank>http://www.amphenolrf.com/pdf/283.pdf?the</A> center pin for 
Amphenol 9913 conectors needs to be crimped with a .116 inch die.?? I've looked 
high and low for a .116 inch die for my crimper and can't find one, I do have a 
.128 inch die and according to the RF parts web site that is the appropiate 
size for crimping 9913 center pins.??? (The crimp for the outer connector seems
to be?a common .429 inch size.)<BR>&gt;&gt;&gt;&gt; <BR>&gt;&gt;&gt;&gt; Google 
searches for .116 inch dies and crimpers are not turning anything up 
either.<BR>&gt;&gt;&gt;&gt; <BR>&gt;&gt;&gt;&gt; I'm wondering if the amphenol 
connectors need a different size crimper than other common connectors ???? I've 
always had good results using amphenol brand connectors and would like to use 
them going forwards.<BR>&gt;&gt;&gt;&gt; <BR>&gt;&gt;&gt;&gt; I've seen several 
other crimpers advertised for crimping 9913 connectors but they don't specify 
the die sizes.? I'm reluctant to order one with out knowing what the die sizes 
are.<BR>&gt;&gt;&gt;&gt; <BR>&gt;&gt;&gt;&gt; Does any one have any practical 
experience they can share with me about crimping N connectors to Belden 9913F7 
cable ??? I'd really like to use crimp style connectors going forwards but I 
want to make sure I crimp them properly.<BR>&gt;&gt;&gt;&gt; 
<BR>&gt;&gt;&gt;&gt; 73's<BR>&gt;&gt;&gt;&gt;
<BR>&gt;&gt;&gt;&gt; Mark<BR>&gt;&gt;&gt;&gt; VE7AFZ<BR>&gt;&gt;&gt;&gt; 
<BR>&gt;&gt;&gt;&gt; <BR>&gt;&gt;&gt;&gt; <BR>&gt;&gt;&gt;&gt; <BR>&gt;&gt; 
<BR>&gt;&gt; _______________________________________________<BR>&gt;&gt; 
<BR>&gt;&gt; <BR>&gt;&gt; <BR>&gt;&gt; 
_______________________________________________<BR>&gt;&gt; TowerTalk mailing 
list<BR>&gt;&gt; <A href="mailto:TowerTalk@contesting.com"; 
ymailto="mailto:TowerTalk@contesting.com";>TowerTalk@contesting.com</A><BR>&gt;&gt;
 <A href="http://lists.contesting.com/mailman/listinfo/towertalk";; 
target=_blank>http://lists.contesting.com/mailman/listinfo/towertalk</A><BR>&gt;&gt;
 <BR>&gt;&gt; <BR>&gt; <BR>&gt; <BR><BR></DIV></DIV></div><br>
      <hr size=1>
Looking for the perfect gift?<a href="http://www.flickr.com/gift/";><b> Give the 
gift of Flickr!</b></a></body></html>
--0-1296860631-1231247136=:69853--
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk



      __________________________________________________________________
Be smarter than spam. See how smart SpamGuard is at giving junk email the boot 
with the All-new Yahoo! Mail.  Click on Options in Mail and switch to New Mail 
today or register for free at http://mail.yahoo.ca
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>