Search String: Display: Description: Sort:

Results:

References: [ +from:wc2l@wc2l.com: 6 ]

Total 6 documents matching your query.

1. [Amps] K3 & THP HL-2.5KFX (score: 1)
Author: William Liporace <wc2l@wc2l.com>
Date: Wed, 25 Jul 2018 19:37:39 -0400
Hi Folks, I think I have the pin outs correctly. I know there is a low output voltage on the K3. I don't know why the AMP does not like the K3. I have the AMP set for Yaesu. That is basically what th
/archives//html/Amps/2018-07/msg00072.html (7,091 bytes)

2. [Amps] THP HL-2.5Kfx (score: 1)
Author: William Liporace <wc2l@wc2l.com>
Date: Mon, 3 Dec 2018 20:29:02 -0500
Hi Folks, I'm having an issue with the THP HL-2.5Kf and I have a couple of questions. I do have the 1.5C firmware. I have it hooked up to a K3. The amp is set to Yaesu band data. I know the amp used
/archives//html/Amps/2018-12/msg00013.html (7,826 bytes)

3. Re: [Amps] THP HL-2.5Kfx (score: 1)
Author: William Liporace <wc2l@wc2l.com>
Date: Wed, 5 Dec 2018 09:39:32 -0500
Thanks! I was headed in that direction... Now to make some room on the bench to work on it!! Will "If the POWER switch is turned on, while OPER/STBY switch is at OPER(operate) position, the orange OP
/archives//html/Amps/2018-12/msg00030.html (10,212 bytes)

4. Re: [Amps] THP HL-2.5Kfx (score: 1)
Author: William Liporace <wc2l@wc2l.com>
Date: Wed, 5 Dec 2018 19:20:08 -0500
I appreciate the help... It was not the OPER/STBY switch. It is actually a DPDT and only using one side. I went ahead and moved it to the other side. Both sides are fine. I was also told that there a
/archives//html/Amps/2018-12/msg00034.html (9,119 bytes)

5. [Amps] THP HL-2.5Kfx Firmware Chip/File (score: 1)
Author: William Liporace <wc2l@wc2l.com>
Date: Wed, 5 Dec 2018 19:22:42 -0500
Hi Folks, I am looking for the chip and/or firmware file for the THP HL-2.5Kfx. That is what I have in there now. I have been told newer may not work. Any help or suggestions would be great!!! TNX Wi
/archives//html/Amps/2018-12/msg00035.html (7,009 bytes)

6. [Amps] THP HP-2.5 Help (score: 1)
Author: William Liporace <wc2l@wc2l.com>
Date: Sun, 30 Dec 2018 17:34:09 -0500
Hi Folks, I have a THP that on startup is displaying the message  "PSE STBY OPERSW!"  after it gives me the THP/firmware version  message. Doing a bit of troubleshooting with a friend, it appears tha
/archives//html/Amps/2019-01/msg00003.html (8,284 bytes)

Current List: 1 - 6
Page: [1]
This search system is powered by Namazu