Dan Unless he as a new version none of the Prism 2.0 or 2.5 cards we have work in SEC mode. I think his comment where talking at TC mode and the power issues. Sincerely Tony Morella Demarc Technology
Gentlemen we have not fully tested this version of firmware but your feed back would be appreciated. This is version firmware 1.42 for the Prism 2.5 cards. http://www.demarctech.com/downloads/prism25
Mel I don't know if Orinoco's new code is the same one that Karlnet released if it is then yes but I am not sure why Orinoco would want standard Prism 2/2.5 drivers to be in there version. We have on
Norm The problems goes all the way back to Intersil on this one as they are the one developing the firmware. We are doing EVERYTHING in out power to add this functionality but WISP are a small spec o
Doug FYI we tested this :) When the cards are in SEC mode with just routing turned on the unit locks up on the cards port. Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 90
Travis For the most part bandpass filters will not help if the interface is within the 2.4Ghz band (IE the channel you are on). It will just "Notch" out the frequencies you are working with. It does
Indra Yes the SEC client can connect to a standard 802.11b AP but only in NAT our running mode. To use bridging AP+ on an AP-1000 is need. Sincerely Tony Morella Demarc Technology Group Office: 908-9
Eric It will work but from a few tests we did I would not recommend using the full stream if using TC in PtMP mode. If the camera supports it doing 5-10 frame per sec would produce better results whi
Dan We have done the FTP test with 20 CPE and a single base station in a lab. The polling did what is should have done, each unit was able to sustain about 27K which is the available bandwidth divide
Bob Yes, our 100mW card does work in an RG-1000 and AP-1000. http://www.demarctech.com/products/relia-wave-100mw-pcmcia-card.html Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 C
HEHE soon my friend :) But you can count on Demarcs 120* and 18Dbi CPE Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202 email: tony@demarctech.
Dong You have this card! Its the one we sent you for testing :) Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202 email: tony@demarctech.com htt
Norm Just to confirm, all the numbers you are reporting where from Karlnet TurboCell correct?? If this is the case, Doug (KN) has report to me that all the Prism cards report back in the same way and
Bill All the test have been done NOT using software as it can come times not be trusted. From what I have been told by KN there is a problem in that the numbers reported back from the radio are not c
Well All Right! This is very good news ;) I know the frustration you are having! We have been trying to duplicate the problem and just could not do it if the cards where inserted the way I listed bef
Norm Can you please confirm you WPOP and client side setup. Antennas, cable lengths etc, as you know the link is bi-directional as such both directions need to be with in spec on TX and RX to operate
Norm When I do the calcs at 11Mb the theoretical number should be about -73dBm at the laptop and -77dBm at the AP. Hmm Give me the lat/long and antenna heights I want to run an path profile using RF
In the process :) Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202 email: tony@demarctech.com http://www.demarctech.com Wireless Solution Provi
Norm What version do you have running on the AP? Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202 email: tony@demarctech.com http://www.demarct
Gentlemen I have a question for the people that have purchased the so called 200mW cards with the FCC ID SL-2511CD-plus2, which I think is almost everyone testing show about 56mW or 17dBm of output f