If you going to run in a contest, what you do it hook up a contest program to the radio and then just run it like any other radio. I'm a DX'er and as with all radios I use, I interface my N4PY softwa
There's no law that says the step size has to be 1 mv. It can be whatever the design allows. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com If the A to D has say, 1 mV per bit resp
And further, the clip point is simply the point where a signal is too large for the A/D converter. So if you have 65536 values in 16 bits, you divide the real dynamic range of the A/D by 65536 and us
Sure you will have problems. You have now exceeded the clip point. For the Flex 6500 that's S9+80. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com SO, if you sample the voltage appe
I have Paragon code that I developed that adds some features. I can't burn eproms anymore but I can help you here. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com I really thing it
I would first replace the battery. You have to remove the front panel to get to it. Once you have the front panel removed, you will see 2 connectors that have about 100 connections each. I would pull
The Omni VI does fold back power based on final current. If the current goes too high, the drive to the finals is reduced. It does not fold back based on SWR. Carl Moreschi N4PY 58 Hogwood Rd Louisbu
I didn't think it was April 1. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com The definition of electromigration is migration of conductor material in a circuit trace due to the mo
The amp key line comes on about 15 msec before RF is produced. This allows the amp relay to transfer. QSK should be fine this way.. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com -
That's not normal. I would do a full reset as follows. 1) Power off Orion. 2) Power On holding the VFO B LCK button. 3) Continue holding LCK button until the radio says "Battery Failure". 4) Power of
Art, I believe you are correct. I would set the ALC pot for 100 watts and not 110. The power indicator is supposed to read watts and not percentage. If you exceed 100 watts, you signal will start to
Also there is the Ameritron 1306 that adds 6 meters and computer control to the 1300. I have one and like it. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Don't let the name fool
It's a good one. I have two of them. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com What else should I be looking at? Tnx 73 Rick, DJ0IP ___________________________________________
My N4PY Orion program will allow you to get all frequency information on HDSDR for SDRplay. I have a method to attach the SDRplay and share antennas with SDRplay. Carl Moreschi N4PY 58 Hogwood Rd Lou
Sounds like something changed on the bias for the finals. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 12/21/2016 2:07 AM, k7mks@comcast.net wrote: My Corsair I draws 9-10 amp
My N4PY Pegasus Plus software allows up to 5 different hardware or software devices to be hooked up to the Omni VII at the same time. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com
Yes, and I believe this was slightly different from Binaural receive. The idea was different pitch signals would seem to come from different directions. Low pitch was all the way to the left and high
I used the cardboard method. It was very easy and foolproof. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 1/22/2017 12:12 PM, Bwana Bob wrote: Yes, there are a couple of ways
Rick, I don't have that firmware. But I do not believe changing the FW will fix the problem. I believe that problem comes and goes with temperature variations. The fix is to get a filter to connect t
I thought the QST article for panadapters was very poor. It recommended using the IF to feed the panadapter. This is an archaic method. Today with the SDR receivers available such as SDRplay, much be