Don When you get this figured out and you determine a source for the black covering and a process to take off the old and put on the new I know there will be many interested in what you did and where
I have been thinking about converting an old Argosy to use it as an external VFO for an Omni-D that I have. I know that this is akin to making a hammer out of a shovel but the Argosy PA is gone and t
I have always wanted a small QRP module that would go inside my RX-320 case I would think that since the 320 is smiliar to the Pegasus that this would be relatively easy to do. I would guess that you
I would be that your right that the Argo has a better receiver and it is already to go just add Carl's software and an antenna. I am afraid that sometimes I like to do things the harder way to learn
I am looking for an Argosy analog or digital front panel, if any of you run across one of these I am most interested since I need to replace mine, it is badly damaged. steve
Can anyone tell me what the equivalent is to the PT3647 RF driver in the Omni-A PA? I had been told that there is a NTE equivalent but forgot the number. Is there a standard JEDEC equivalent as well?
I have been fighting a problem in my Omni-A and it is beginning to appear that the power supply is not up to par. It doesn't put out 13.8 volts under load very well... I wonder if anyone would happen
I am looking for a beyond repair Argosy....As long as it has a good case I would be interested but really would rather have it not working since I am only interested in the case and front panel. If a
I have an Omni-A and am wondering if the red vertical bar that indicates the 100Khz marks is supposed to be illuminated. Mine is dark and is hard to see at times and am wondering if I have a lamp bur
Boy this is a problem that I have never seen before. My Omni-A has low power out on 14,21 and 28.0 but is ok on 28.5, by low power I mean less than 80 watts out. On 3.5,7.0 and 28.5 I can get 100+ ou
I tried the same trick by changing my refresh to 75 and it helped a lot, I then upped it to 85 and it helped even more and finally I am at 100 hz and all the noise that I was seeing around the 14.070
Does any one know the correct freq that the BFO's should be set to when aligning the Omni-D? I have tried the method outlined in the manual and it seems a bit of a difficult way and can lead to some
I took a look at the Argosy manual and they both use the same circuitry and the same procedure to align the carrier oscillator. If they got the Argosy one wrong then I have to assume as you did that
I have sent an email off to Ten Tec to see what they have to say regarding the proper procedure for setting up the Carrier Oscillator on the Omni-D. When I used the procedure in the manual I had real
Does any one know if there is an adjustment pot inside this power supply that adjusts current limiting? If so can you tell me where it is located...I don't have a manual on my 262M.. Thanks Steve
Hmmm....I recall that they did answer one tech inquiry of mine regarding mods to the Omni-D but just in case they no longer reply I will give them a call in morning...Thanks for the heads up. steve -
Now that Al has found his fixer upper maybe someone will have a rig that they want to see brought back to life and willing to part with. Cosmetics do not matter or condition, let me know if you have
Steve That's a good start, I will combine that with the capacitor that I have and then we got something. But seriously, I am looking to bring one back from the dead and I am sure there are few more o
I am trying to understand the differences in performance of the Omni V as compared to the Paragon. Setting aside for the moment the differences in the keyboard layouts and the man machine interface w
Well to make a long story short, I have lost my instructions for PTO rebuild. I have taken these apart before and had purchased a rebuild kit in the past but this one that I am working on now was not