Hi All, Due to downsizing I wish to sell off the following: TT Corsair II with PSU, Paddle and External VFO plus CW filter. Offers over £350 TT Omni VI modded to Plus at the factory with CW XTAL filt
Hi All. I have a Corsair II in good order with an external VFO, original PSU, and with three xtal filters installed, 1 ssb and 2 cw (500 and 250 probably). This equipment has been in my family since
Hi, Also had that problem some years ago; as far as I remember the pot is accessible from through the bottom cover. I also thought it might be the pto, but researched the problem on line and found ou
Hi, I suggest that you should check the electrolytic smoothing capacitors, and the pass transistors for short circuits before fixing the bridge rectifier circuit. 73 Tim gm4lmh On 21/09/2014 03:30, A
Hi, I have a 238 B ATU that is surplus to requirements due to the sale of my Titan amplifier a while ago. Original packing and instruction. Has has little use over 100 Watts as I operate CW most of t
Hi Rick, There used to be a TV detective series on the ITV channels named Morse, and the code for Morse was hidden in the signature tune. http://www.youtube.com/watch?v=cCPqcu9p7mM 73 Tim gm4lmh On 1
Hi All, As far as I can remember micro farad was designated mmf in the days of old. Tim gm3eew Stuart Rohre K5KVH _______________________________________________ TenTec mailing list TenTec@contesting
Hi Wade, Just looked at my manual, and your memory serves you well. Looks like a likely cause of the problem. 73 Tim gm4lmh -- From: "wade staggs" <tvman1954@gmail.com> Sent: Saturday, July 14, 2012
Hi Wade, Just sent Ben a scan. 73 Tim gm4lmh -- From: "wade staggs" <tvman1954@gmail.com> Sent: Saturday, July 14, 2012 5:58 PM To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com> Subject:
Hi, Not unless you want to lose your fingers. 73 Tim gm4lmh Another list member and I were wondering......If a scope's front panel says max 250 volts P/P....does that mean if you have a X10 probe, yo
Hi, It is R3 on the mixer board and it affects 10, 21 and 28 Mhz bands. See page 3-7 of the Corsair II manual. Suggest you redo the set up procedure to exercise the pot. 73 Tim gm4lmh The warble on m
Hi All, I run an Omni VI opt3 on a 961, and that also runs much hotter than I expected. I do not remember the Omni V or Paragon doing the same. 73 Tim gm4lmh -- From: "W8BVH" <w8bvh@sbcglobal.net> Se
Hi Richard, I have an Omni V with stock filters, the other are in a VI opt 3 that I got last year. It currently has the updated control chip installed, but I have the old one stored somewhere. I am a
Hi, Have you got the jumper fitted on the back where the external vfo connects? Funny things happen without it. Tim gm4lmh -- Original Message -- From: "g p" <n2wjw@yahoo.com> To: <tentec@contesting.
Hi Malcomb, Sent you a message regarding an Omni VI Opt 3 that I have in the UK. Stock filters and no psu. Unfortunately the message got bounced. Would you be interested? 73 Tim gm4lmh Hi all, I live
Hi Mike, I have a 238 that matches the Corsair I colour scheme. The other problem is that it is in the UK. Would this be of any interest? 73 tim gm4lmh -- Original Message -- From: "Mike Schatzberg "