Hello Is there interfaces sold on the market ( to be use for RTTY CW SSB ) that are installed only on the radio accessory connector at the back of the radio but not on the front MIC connector......?
On SSB mode my macros operates now and looking on the windows & writelog (sound boards) controls on a second screen at the same time. Both right and left audio output level control ar used? If I move
My writelog software now works on any mode RTTY CW SSB including macros. But I have a problem WITH SSB TX when I add insulation transformers (one on RX the other on TX ) in the computer audio output
My writelog software now works on any mode RTTY CW SSB including macros. But I have a problem WITH SSB TX when I add insulation transformers (one on RX the other on TX ) in the computer audio output
Alfred KE1FO Thank you so much for your rapid support. You got it right on the target center it works now on SSB...! I was in parrallele across the 2 insulation tranformers and no reference to ground
Alfred Again now everything works find all modes all bands. I found the answer about insulation transformer without stereo to mon adaptor. Before you found my problem where I did'nt install a stereo
With the help Alfred KE1FO and many other WL group members we completed the installation of WL on all 3 modes, ssb cw rtty. But now I return to my laptop with same type of installation. WL + mmtty +
I has been settled this afternoon. I found another cable that was possibly dammaged. There was a wrong connection on RTTY & CW side. Almost same problem there was on the PC. Also I been hit by a majo
( It ) has been settled this afternoon. I found another cable that was possibly dammaged. There was a wrong connection on RTTY & CW connector side. Almost same problem there was on the PC. Also I bee
1: 1 Isolation transformers on PC input ( from transceiver ) and or output for audio TX. What should be the perefered impedance on on both side on each of them. Gilles VE2LX == ______________________
Hello Where do we find that driver for EXTFSK mentionned at hamsoft web site If you are using Windows 2000 or XP, you need the DLPORTIO driver Gilles ve2lx == ________________________________________
Is there some one operate the Icom pro 3 in the SSB-N (narrow or digital ) mode...? Is it much better then stdr SSB mode and is it really usefull ...? Gilles ve2lx ve2lx@sympatico.ca ________________
during CQWW WPX and in some pass contests I experiment a curious problem. 1...In RTTYrite windows hwere all calls are shown very often for an unknown reason calls are not in different colors...? (yel
Dave thank you for the answer i'll do that today bye Giulles ve2lx -- -- Original Message -- From: "Dave Hachadorian" <K6LL@ARRL.net> To: <writelog@contesting.com> Sent: Sunday, February 10, 2008 6:3
MapCallOnSpace - does'nt map the calls ( even if I push space bar ) even if the script of the command is correct and placed next line after [ENTRY] here is the direct copy of the script in WL.ini fil
special feature key INSERT ( insert override calls ) set in writelog.ini file. When activated it should capture certain calls. But in my case when insert key is pushed it start my macro F2 VE2LX whic
In Writelog manual it is writen that we can write the radio address in WL ini file (Icom IC-756PRO=0x12) ( IcomIC-756PRO 3 ?=???? or 6He ) . What would be the advantage to write it in WL.ini file whe
In Writelog manual it is writen that we can write the radio address in WL ini file (Icom IC-756PRO=0x12) ( IcomIC-756PRO 3 ?=???? or 6He ) . What would be the advantage to write it in WL.ini file whe
Gary Tel him that I recorded 50 different SSB messages with windowsXP recorder in fact because there was a delay between the time I activate the message and the message transmission, and I first foun
I bought one USB to 2 SERIAL from SIIG recently and it works grate on my PC and laptop. Gilles ve2lx == -- Original Message -- From: <CATFISHTWO@aol.com> To: <n1rl@earthlink.net>; <lists@microham-usa