The "D" includes: TCXO-1 High Stability Oscillator (+/- 0.5 ppm vs. standard +/- 2.0 ppm) BPF-1 Second Receiver Bandpass Filter Unit (allows true dual receive on separate bands) XF-455K-262-01 (2.6
I will be in Brussels 6-7 January and London 8-10 January. My schedule is relatively clear both evenings in Brussels and Wednesday evening in London. Anything interesting during that time? 73, ... Jo
Barry, No ... Yaesu used some extra switching diodes to select the 2.4 KHz 3rd IF (ceramic) filter if the optional crystal filters had not been installed. There are (were) four optional 3rd IF (455 K
Punching "sub" followed by "2.0" or "2.4" should also restore signal. The wide or narrow filter is selectable independent of the operating mode on the sub-receiver. 73, ... Joe, K4IK
The "brown" wire shorted the input to the driver stage in the 11 Meter (AUX) bandswitch position to prevent the FT-101E from transmitting on 11 meters. If, for example, one were to replace the 11 Me
Leon, I would trust Yaesu's manual. However, put the pin part of the plug into the jack on the back of the FT-1000(D) and confirm the voltages with a digital voltmeter. The manual gives "band A, Band
OK folks. I've messaged a couple people directly but this has gotten out of hand. This discussion is over NOW! Anyone who continues the off-topic posting will be removed from the list as I will not a
The FT-1000D has no menu. What filtering are you referring to? The PKT mode shifts the display offset and IF passband center frequency based on the settings of dip switch positions 1 & 2 ([PKT] under
Paul, What are you trying to accomplish? In PKT the FT-1000MP does the following: 1) Offset the display to the "center of the channel" (i.e., half way between the expected mark/space tone ... -2125 H
Operator's Manual (Page 7) shows pin 1 to be to the LEFT of the "notch" when looking at the wiring (cable) side of the PLUG. Pins appear to be numbered clockwise 1 through 5 with pin six being in the
Yes, there are two DIN-8 standards and Yaesu uses the less common of the two. I believe the pins of the more common connector are along a 270 degree arc ... Yaesu and Kenwood use a 262 degree arc. O
Gee ... I guess it's time to get my SP-5/59Y out of the closet and list it. That's at least as much as the pair commanded when they were new! 73, ... Joe, K4IK ______________________________________
The following was posted to the Topband, Towertalk and Amps reflectors today. I have no further information and have heard no discussion of the future of eHam.com or the contesting.com reflectors. I
The radio is rated for 200 Watts ... I suppose an individual could "push" the ratings by tweaking the internal ALC limits. However, at more than $450 for a set of replacement final transistors I wou
It's hardly a guess since every advertisement, the brochure on Yaesu's US web site and the brochure/specifications on Yaesu's far east web site all say 100 Watts. The only place 200 Watts is even men
If you do, please post the test procedure, equipment configuration and current calibration certificate for the equipment. 73, ... Joe, K4IK _______________________________________________ Yaesu mail
If you do, please post the test procedure, equipment configuration and current calibration certificate for the equipment. 73, ... Joe, K4IK _______________________________________________ Yaesu mail
The FT-1000MP/MKV uses a pair of Phillips BLF-147 FETs rated at 150 watts each. The complete datasheet is: http://www.platan.ru/pdf/1dist/philips/BLF147_3.pdf In class AB, third order products are l
The firmware in the FT-1000(D) is a standard EPROM and is quite easily replaced. One must remove the covers, "fold down" the front panel, and remove one shield cover (as I remember). 73, ... Joe, K4I