Here are three bugs which I have found in the recent 2.044A firmware update. I have reported them to Ten-Tec: The fix "fixed restoration of bandwidth when recalling USER memory" does not work correct
Last night I observed a problem somewhat similar to what Rick is describing. I noticed that what ever setting the variable BW is reading prior to shutting the radio off is not the same BW setting tha
Hi Steve, It certainly looks like it could be related. When I cycle the power on my rig, it sets the BW to 100 Hz for SSB, to 2400 Hz for FSK, and to 1000 Hz for CW. Those are the same values which B
I tried it a few times. When power is turned back on, it resets to default values of 100 on CW and 3000 on SSB. Definitely a bug. 73 Ray W2RS In a message dated 6/17/2010 6:00:33 P.M. GMT Standard Ti
Yes, that is correct. Where it is pulling the default value from I am not certain, nor am I certain that everyones default values are the same, however, what is key is that it is returning some defau
YES MINE DOES THE SAME THINK ROD W3KRQ -- Original Message -- From: "Rick Borken" <rickb@cpinternet.com> To: "Steven Kline" <skline4@verizon.net>; "Discussion of Ten-Tec Equipment" <tentec@contesting
Thank you Rod. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Just to throw a jinx in the comments, my OII returns to whatever I had setup before I turned her off. BW, PWR, etc, same with User 1 and User 2. I find the 2.044 very similar to 2.039 version. Could
Same here....No problem. Plays very well. Bad download? W9XX -- Email Provided by Hoosier Broadband - Indiana's #1 Source for High-Speed Wireless Internet! www.hoosierbroadband.com -- _______________
Ditto with mine. Goes to what I had set previously. Troy, W6HV _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/t
they are talking the dsp bw not the trsnsmitt bw i set my dsp bw to 2800 turn off and back on the dsp bw goes to 3000 -- Original Message -- From: "Troy W6HV" <w6hv@verizon.net> To: "Discussion of Te
Not here. I can cycle the radio on and off and the set DSP BW in all four (A thru D) band registers and all are recalled, every time, with complete accuracy to what I set last. 73, Bob K8IA, Presiden
Yes, thank you Rod and all. I needed to be more specific in my terminology. As Rod stated I am speaking of the DSP variable BW. It was a good suggestion, and I will reload the software load and do th
That's what I am talking about; the receive BW stays put. No problem. I set to, say 450 on 14,020, later go to 80 meters with it set to maybe 600 then later return to 20 and it's still set to 450. __
I just loaded version 2.044A and came from 2.039d. The rig automatically did a master reset going from the old version to the new. I am experiencing the same thing as has been reported. If the BW on
tor, 17 06 2010 kl. 23:40 -0400, skrev Toby Pennington: Am I correct in assuming that you omitted the update from 2.039D to 2.043B and went directly from 2.039D to 2.044A? Someone I know had done tha
Is anybody else using the non-default display colors? Upon power on/off, the default colors always come up, not the selected one. Mike, WA1SEO _______________________________________________ TenTec m
Mike, I am using the non-default display, selection 3 on the display menu, and in my exercise of cycling the radio on and off replicating the variable DSP BW issue, I did not have any problems with t