Hey Jay, I think you were given bad advice, the filament choke would not be
an issue, it would be the plate choke.
BOB
-----Original Message-----
From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On
Behalf Of Jay Musikar
Sent: Saturday, March 03, 2007 4:45 PM
To: Pete Smith; Amps@contesting.com
Subject: Re: [Amps] Loading SB-220
Pete -
You loss the bet. There was never an issue with of
arcing in my SB-220. The advise came from a number of
SB-220/221 users when I asked the same question.
The reason given to me was that damage to the filament
choke could occur when used on 17m and 12m running
full power.
Since the output is quite sufficient in the CW/Tune
position, use under SSB never entered my mind.
I have no problem with loading the amp "heavy" in the
CW/Tune position. I don't believe in "Light" loading.
73,
Jay/AF2C
--- Pete Smith <n4zr@contesting.com> wrote:
> I don't think that is correct either, Bob - I use my
> SB-220 on 12 and 17 in the SSB position all the
> time. I'd be willing to bet that this advice is
> based on having arced the tuning capacitor a time or
> two while finding the right setting with the loading
> too light.
>
>
> >Use LV position, and why is that Jay? I would
> agree to get within a
> >reasonable setting with LV and pop her over to
> SSB... But why do you say
> >stay with LV?
> >
> >BOB DD
> >
> >-----Original Message-----
> >From: amps-bounces@contesting.com
> [mailto:amps-bounces@contesting.com] On
> >Behalf Of Jay Musikar
> >Sent: Saturday, March 03, 2007 1:33 PM
> >To: Win; Amps@contesting.com
> >Subject: Re: [Amps] Loading SB-220
> >
> >GA Win -
> >
> >1. Loading on the WARC Bands must be done in the
> >CW/Tune Position.
> >
> >2. Do not operate the amplifier in the SSB position
> on
> >the WARC Bands.
> >
> >3. 17m
> >Band Switch - 15m
> >Tune - Top of the 40m markings
> >Load - 4.0
> >
> >4. 12m
> >Band Switch - 10m
> >Tune - 20m (just left or CCW)
> >Load - 4.0
> >
> >The are a number of variation on which Band Switch
> >Position to use and relative Tune and Load
> settings.
> >
> >In either case DO NOT use the SSB postion (HV).
> >
> >Good Luck es 73,
> >
> >Jay/AF2C
> >
> >--- Win <w0lz@winlyn.us> wrote:
> >
> >> Can someone comment on loading the SB-221 up on
> 18
> >> and 24 MHz. using the
> >> existing band selections. Will the input Z
> change
> >> much? Which band switch
> >> positions to use for each band? At the moment I
> am
> >> really only interested
> >> in 18 MHz. As conditions get better, I will
> >> probably become interested in
> >> 24 MHz.
> >>
> >> Thank you in advance.
> >>
> >> Win, W0LZ
> >
> >
> >
> >
>
>___________________________________________________________________________
_
> >________
> >Finding fabulous fares is fun.
> >Let Yahoo! FareChase search your favorite travel
> sites to find flight and
> >hotel bargains.
> >http://farechase.yahoo.com/promo-generic-14795097
> >_______________________________________________
> >Amps mailing list
> >Amps@contesting.com
> >http://lists.contesting.com/mailman/listinfo/amps
> >
> >
> >
> >_______________________________________________
> >Amps mailing list
> >Amps@contesting.com
> >http://lists.contesting.com/mailman/listinfo/amps
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
____________________________________________________________________________
________
Bored stiff? Loosen up...
Download and play hundreds of games for free on Yahoo! Games.
http://games.yahoo.com/games/front
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|