Thanks for the sage advice.
Sounds like you're basically saying, don't over complicate it.
73, Don KO7i
----- Original Message -----
From: "Carl" <km1h@jeremy.mv.com>
To: "Don Jones" <ko7i@comcast.net>, amps@contesting.com
Sent: Saturday, March 29, 2014 6:55:33 PM
Subject: Re: [Amps] Drake L-4B Should I or Shouldn't I?
Consider how many of this very popular amp are still used regularly without
making "Internet Changes" to join a few other lemmings.
Carl
KM1H
----- Original Message -----
From: "Don Jones" <ko7i@comcast.net>
To: <amps@contesting.com>
Sent: Saturday, March 29, 2014 9:12 PM
Subject: [Amps] Drake L-4B Should I or Shouldn't I?
> Last year I picked up a L-4B from an estate sale. About a month ago I
> tried to fire it up. Looks like I got some problems to repair first. I did
> hear a thump come from the transformer of the L-4PS as it charged the high
> voltage cap bank. No biggie, also I did see the 3-500's light up in the RF
> deck.
>
> What I did not see was any indication of High Voltage being present on the
> L-4B's voltage meter. Fingers crossed I do not have a blown meter. What
> should I see for pin to pin resistance of the High Voltage meter? Also
> what resistance should I see for the plate current meter? This has me
> puzzled, I would think that the meter should have shown that high voltage
> was present. I presume that this is a proper assumption. Correct?
>
> Since I suspected there was problem, I stopped there and did not attempt
> to "key" the amplifier and see if it would tune up. I pulled the 240VAC
> power plug and let it set for a few days. After which I opened the high
> voltage power supply section and inspected it internally. The power supply
> has the original paper caps that came with it from the factory. I did not
> see any blown diodes or smoked resistors, the paper caps still had their
> guts which is a good sign.
>
> After some thought and having good service from Harbach Electronics with a
> Clipperton-L power supply rebuild kit I decided to order one for my L-4PS
> so I could get those old caps and diodes replaced. I also ordered a new
> rebuild kit for the front panel power switches and a soft start kit for
> the amplifier too.
>
> As for the Should I or shouldn't I question...
> I am going to operate this amplifier with an out board QSK switch and bias
> control. I am thinking about hard grounding the grids and installing a 50k
> ohm resistor in the B- lead to cut off the tube instead of relying on the
> +150Vdc (or so) cathode voltage as designed from the factory. I have
> heard "internet stories" claiming that the L-4B can become unstable if the
> grids are hard grounded. Something about the gain of the tubes becoming
> higher and unstable. Is this true or not? I do want to use this amplifier
> on all bands including 10 meters.
>
> My bottom line goal is to run this amplifier at about 750 to 800 W rms out
> and enjoy it for many years to come. Looking for some technically sound
> advice and objective criticism. Sorry for being long winded. Thanks!
>
> 73, Don KO7i
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2014.0.4354 / Virus Database: 3722/7268 - Release Date: 03/29/14
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|