I have not seen anything that specificly allows the control bits.
I have seen some advertisements for bi-directional parallel port USB
converters.
My needs are different, I need band data only.
I use two microham microkeyer for SO2R, N1MM is pretty good about keeping
the PTT straight from the software, One microkeyer has to be set up for
Serial port CW, the other is set up for winkey CW.
Best wishes,
Rich
K5SF
>From: "Joe Subich, W4TV" <w4tv@subich.com>
>To: "'Richard Detweiler'"
><rdetweil@hotmail.com>,<CQ-Contest@CONTESTING.COM>
>Subject: RE: [CQ-Contest] SO2R with modern computers
>Date: Mon, 24 Jul 2006 14:00:00 -0400
>
>
>Rich,
>
>Which USB to parallel adapters have drivers that allow port
>mapped bit flipping required by Writelog and N1MMLogger?
>
>73,
>
> ... Joe, W4TV
>
>
>
>
> > -----Original Message-----
> > From: cq-contest-bounces@contesting.com
> > [mailto:cq-contest-bounces@contesting.com] On Behalf Of
> > Richard Detweiler
> > Sent: Monday, July 24, 2006 11:46 AM
> > To: yo3ctk@alltrom.ro; CQ-Contest@contesting.com
> > Subject: Re: [CQ-Contest] SO2R with modern computers
> >
> >
> >
> > For your specific question, there are available
> > bi-directional parrallel
> > port to USB converter cables. one end is USB, the other end
> > is a parrallel
> > port.
> >
> > I have had to design band decoders for ICOM, and Yaesu
> > radios, to drive the
> > 419 (sink) and six pack (source) devices. For Station
> > automation, would
> > then, for ICOM, convert those band bits back to Yaesu format
> > to feed the LPT
> > port.
> >
> > Almost all programs and some external devices will present
> > band data to the
> > parrallel port or take band data from the parrallel port in
> > Yaesu Format.
> >
> > Best wishes,
> > Rich
> > K5SF
> >
> >
> >
> > >From: "Yo3ctk" <yo3ctk@alltrom.ro>
> > >To: <CQ-Contest@contesting.com>
> > >Subject: [CQ-Contest] SO2R with modern computers
> > >Date: Mon, 24 Jul 2006 16:47:50 +0300
> > >
> > >Hi all,
> > >
> > >We at YR7M would like to try our hand at SO2R. We already
> > have a moderately
> > >competitive M/S setup, essentially equipped with monobanders and CAT
> > >radios, along with ICE band filters, band decoders and Six
> > Pack antenna
> > >switching system. We're using WL software. I was looking at
> > the DX Doubler
> > >for completing the automation of the station. However, it
> > seems that a
> > >parallel port is essential for this device, and our
> > computers are all
> > >laptops, with only USB ports.
> > >
> > >Is there a modern alternative to the DX Doubler (or similar
> > boxes) that are
> > >only using USB ports? Thanks for any hint.
> > >
> > >73 de Mike, YO3CTK
> > >_______________________________________________
> > >CQ-Contest mailing list
> > >CQ-Contest@contesting.com
> > >http://lists.contesting.com/mailman/listinfo/cq-contest
> >
> >
> > _______________________________________________
> > CQ-Contest mailing list
> > CQ-Contest@contesting.com
> > http://lists.contesting.com/mailman/listinfo/cq-contest
> >
> >
>
_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest
|