TenTec
[Top] [All Lists]

Re: [TenTec] Apartment antenna help

To: <wb5jnc@gulseth.net>,"Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Apartment antenna help
From: "GARY HUBER" <glhuber@msn.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Mon, 27 Mar 2006 11:53:31 -0600
List-post: <mailto:tentec@contesting.com>
Consider using a LDG or similar end fed wire automatic antenna tuner at the 
window with counterpoises for each band. A single quarter-wave (on the lowest 
band used) wire should provide good results.


Best regards,
Gary - AB9M
CSM(r) G.L.Huber
9679 Heron Bay Road
Bloomington, Illinois 61704
(309)662-0604
www.csm-gh.com<http://www.csm-gh.com/>
csm-gh@www.csm-gh.com<mailto:csm-gh@www.csm-gh.com>
gary.huber@us.army.mil<mailto:gary.huber@us.army.mil>
wm@fifthinfantrydivision.com<mailto:wm@fifthinfantrydivision.com>
National Webmaster for The Society of the Fifth Division
www.societyofthefifthdivision.com<http://www.societyofthefifthdivision.com/>
  ----- Original Message ----- 
  From: Al Gulseth<mailto:wb5jnc@gulseth.net> 
  To: tentec@contesting.com<mailto:tentec@contesting.com> 
  Sent: Monday, March 27, 2006 7:53 AM
  Subject: [TenTec] Apartment antenna help


  Greetings all,

  I'd like some "brainstorming" help on an antenna for my dad. He is on the 
  third floor of an assisted living apartment facility, and we've been trying 
  to figure out if we can get him on the air from there (even on a limited 
  basis). Dad has been trying some indoor antenna setups (such as the Hamstick 
  type dipole arrangements) but apparently to no avail. I suspect this has to 
  do with the construction of the building (i.e. iron frame etc.)

  I have talked to the head of the maintenance department at the facility and 
he 
  seems to be willing to work with me on an antenna, but obviously it needs to 
  be as unobtrusive as possible as well as require as little alteration to the 
  building as possible. Since dad primarily like to operate 40/30/20M, what I 
  am currently thinking as a solution is a 22' wire (either horizontal or 
  vertical) attached to the outside of the building with a bead of clear 
  caulking or RTV. I would need to get this through a window, so I am 
  envisioning using a short piece of a "sandwich" of 1/2" - 3/4" wide thin 
  copper strip/flashing with thick plastic tape on either side so it can 
  (hopefully) be formed so that the window can be closed with it in place. I 
  realize that there would probably be some coupling to the window/frame as it 
  is aluminum. The 22' length mentioned is chosen as I am of the impression 
  that it is a good compromise length that is easy to load on 20-40M. This 
  would be balanced with a 22' counterpoise along the baseboard inside and fed 
  via an SCG (237?) autotuner placed where the antenna comes in through the 
  window. (Hope I'm making sense here with all this....) Another possibility I 
  have considered would be something similar to the B&W/MFJ apartment antenna 
  but with the matching network relocated to inside the building (again 
  possibly using the SGC autotuner along with the requisite counterpoise).

  What is the possibility of this actually working (obviously on a rather 
  limited basis)? Any comments or suggestions? BTW this _is_ Ten-Tec related as 
  dad would be using this with his Delta (probably at quasi-QRP levels of 20W 
  or less due to the possibility of TVI etc.)

  -- 
  TNX/73, Al

  NOTICE to spammers and email address harvesters: you are hereby prohibited 
  from harvesting, reselling or redistributing this email address in any form, 
  or sending unsolicited commercial email ("spam") to it. Should you choose to 
  violate this prohibition, you agree that you will compensate the holder of 
  this address according to the following schedule: for harvesting this address 
  (by manual or automatic means), $100,000 per incident; for reselling or 
  redistributing this address, $10,000 per copy; and $1,000 per unsolicited 
  message ("spam") sent to this address. You also agree that you will 
  relinquish any or all business and/or personal assets necessary to satisfy 
  this obligation and any associated costs of collection and/or legal fees. 
  Failure to read this notice does not release you from liability in this 
  matter.
  _______________________________________________
  TenTec mailing list
  TenTec@contesting.com<mailto:TenTec@contesting.com>
  
http://lists.contesting.com/mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>