TenTec
[Top] [All Lists]

Re: [TenTec] Orion 2 output power

To: "Ron Castro" <ronc@sonic.net>, "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Orion 2 output power
From: <wow_chf@hotmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sun, 7 Feb 2010 19:46:36 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I would have to go to the trouble of reading the schematic, but I guess I 
assumed that it is the maximum permissible collector current set.  This 
would be how Ten Tec protects the final transistors.

When I have a chance I will look and see for sure.  I really can't say for 
sure without looking at the roadmap.

Mike
W2AJI

--------------------------------------------------
From: "Ron Castro" <ronc@sonic.net>
Sent: Sunday, February 07, 2010 7:06 PM
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Orion 2 output power

> Just out of curiosity, what does the "IC" pot do?
>
>            Ron Castro
>  Chief Technical Officer
>     Results Radio, LLC
>                N6IE
>       www.N6IE.com
>
> ----- Original Message ----- 
> From: "Mike Schatzberg " <wow_chf@hotmail.com>
> To: "Discussion of Ten-Tec Equipment " <tentec@contesting.com>
> Sent: Sunday, February 07, 2010 3:03 PM
> Subject: Re: [TenTec] Orion 2 output power
>
>
>> The ALC set does not calibrate the meter, it will adjust the maximum
>> output. Pse see the procedure on my website. Mike W2AJI
>>
>>
>> -----Original Message-----
>> From: shristov
>> Sent: 2/7/2010 9:48:11 PM
>> To: Discussion of Ten-Tec Equipment
>> Cc: 'Discussion of Ten-Tec Equipment'
>> Subject: Re: [TenTec] Orion 2 output power
>>
>>
>> Adjust the ALC SET pot (R179) on the A5 IF Board, beneath the speaker.
>>
>>
>> 73,
>>
>> Sinisa  YT1NT, VE3EA
>>
>>
>>
>> ----- Originalna poruka -----
>> Pošiljalac: Steve Narducci <steve@ndwave.com>
>> Datum: Nedelja, Februar 7, 2010 22:07
>> Tema: [TenTec] Orion 2 output power
>> Primalac: 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
>>
>>>
>>> I picked up a second hand Orion 2 six months ago.
>>> The output power is off on its reading as I am sure the previous owner
>>> played with this.
>>> While reading 65 watts it really puts out 100W.
>>> It will go way above 100W if I run her up.
>>> However, I really want to bring it back into specs.
>>> Anyone have a how-to guide on doing that?
>>>
>>> Thanks in advanced!
>>>
>>> Steve W9SN
>>>
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>