Towertalk
[Top] [All Lists]

Re: [TowerTalk] Nut & Bolt Sealant

To: Keith Dutson <kdutson@sbcglobal.net>, "towertalk@contesting.com" <towertalk@contesting.com>
Subject: Re: [TowerTalk] Nut & Bolt Sealant
From: Gedas <w8bya@mchsi.com>
Date: Tue, 7 Sep 2021 23:21:42 -0400
List-post: <mailto:towertalk@contesting.com>
Hi Keith. I have a lot of experience with epoxies since I was a kid (dad was head of QC at a major adhesives firm)......I love the stuff but I am trying to stay away from a 2-part compound. But the properties of epoxy is what I am after, consistency and strength, cure time, etc.

Gedas, W8BYA EN70JT

Gallery at http://w8bya.com (under repair)
Light travels faster than sound....
This is why some people appear bright until you hear them speak.

On 9/7/2021 9:57 PM, Keith Dutson wrote:
To achieve a permanent bond use epoxy resin. I prefer J-B Weld.

73, Keith NM5G

On Tuesday, September 7, 2021, 08:47:59 PM CDT, W7TMT - Patrick <w7tmt@outlook.com> wrote:


You might want to give 3M 5200 adhesive/sealant a look. It comes in two formulas. Regular and "Fast Cure". The fast cure skins over in an hour or so and is fully cured in 24 hours. The stuff is incredibly tenacious and is often misused in the marine world where a permanent bond is not really what's desired. In your application, the use  of heat, no blow torch required, just a good heat gun, will soften it and allow disassembly at a later date. There are also chemical de-bonders that will release the bond. Highly UV resistant. Check-out the specs and see if it might do the job for you.

Comes in large tubes (9 or perhaps 11 oz.) and small tubes approx. 3 oz. The instructions warn that it must be used within 24 hours of opening. I've successfully kept it much longer by squeezing out a bit and then quickly sealing over the opening with tape. It's a moisture cure product so sealing it well and quickly is the key

73,

Patrick, W7TMT

-----Original Message-----
From: TowerTalk <towertalk-bounces@contesting.com <mailto:towertalk-bounces@contesting.com>> On Behalf Of Gedas
Sent: Tuesday, September 7, 2021 18:21
To: towertalk@contesting.com <mailto:towertalk@contesting.com>
Subject: [TowerTalk] Nut & Bolt Sealant

I am looking for a product that I can dispense via a few drops onto assembles hardware that will dry hard, bond, and resist weathering and UV.

I assumed Locktite Blue or Red would do that for me but I have since learned there are dozens & dozens versions. I clearly picked the wrong products as they never "dried" or hardened. I have 263 Red and 242 Blue. Even a week after application both can be rubbed off flat aluminum with little effort.......not what I am after.

For lack of a better description is there something out there that has the consistency of thick nail-polish that will dry hard and help keep the hardware from coming loose?

Gedas, W8BYA EN70JT

Gallery at http://w8bya.com <http://w8bya.com >(under repair) Light travels faster than sound....
This is why some people appear bright until you hear them speak.


_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com <mailto:TowerTalk@contesting.com>
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com <mailto:TowerTalk@contesting.com>
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>