Hello to all. Well I got the WlFlex Lib 11.27 up and running now. Seems
to communicate with the Flex very well. I do have a few probems:
To run MMTTY Plug in and get the PTT to work, I do have to run the Flex
CAT. No problem. RTTY and CW work fine.
BUT running RTTY I find that if I click on a spot for RTTY it puts the rig
in DIGU and NOT DIGL as it used to. Everyone knows, including WL authors,
that RTTY is most always in LSB.
2nd Since the FLEX doesn't support standard RTTY Tones of 2125/2295 I have
been using low tones with MMTTY, Mark 1445. This has been working well as
the RTTY tones now pass through the CW filter.
I added an "offset" to the WL.ini file so the Spots and sending Spots would
be correct. I now find that the offset now doesn't work and now reports
the carrier frequency. Example below:
COM4_DIGITAL_OFFSET_HZ= -1445
FlexSlot2_DIGITAL_OFFSET_HZ= -1445
I only guess at the what the FlexSlot2 is looking for.
Joe K0BX
On Mon, Jul 6, 2015 at 3:47 PM, Keith Regli <keith@kregli.com> wrote:
> Hey Joe,
>
> I tried it a little with my 6500 this morning. So far not much luck with
> the new driver. I don't think you'll have to uninstall/reinstall stuff to
> switch as the comm happens on the Ethernet rather than a serial port; so no
> real conflicts (although I wouldn't try both at the same time...).
> Hopefully others with have had more success. I'll be trying again later,
> but it's still a "Kenwood" until I learn more.
>
> Keith (K7KAR)
>
> On Mon, Jul 6, 2015 at 8:46 AM, joeduerbusch <k0bx@arrl.net> wrote:
>
>> I own a Flex 6300. I have been a Writelog (WL) User for a very longtime.
>> I use WL as my on-line log both in and out of contests. I then upload the
>> logs into DXbase.
>>
>> Here is my question. I have been looking at the new rig drive that WL
>> just
>> came out with called WlFlexLib 11.27. It seems from the instructions that
>> it replaces the "CAT" control that comes with the Flex software? Should I
>> disable or delete Flex's CAT control? Although I use WL for SSB, CW and
>> RTTY logging, I still use FlDig for Psk. Am I going to have to uninstall
>> the WL driver and reinstall the Flex CAT control??
>>
>> I have seen no discussion about this driver.
>>
>> Thanks Joe K0BX
>>
>> --
>>
>> #1 Honor Roll Mixed
>> Honor Roll RTTY
>> 5BDXCC Plus 30,17,12
>> 5BWAS
>>
>>
>> Stop the insanity!
>> Please do not add me to any distribution lists (Joke, Stories or Junk)
>> without my permission.
>> _______________________________________________
>> WriteLog mailing list
>> WriteLog@contesting.com
>> http://lists.contesting.com/mailman/listinfo/writelog
>> WriteLog on the web: http://www.writelog.com/
>>
>
>
>
> --
> Keith Regli
> mailto://keith@kregli.com
> http://www.kregli.com
>
--
#1 Honor Roll Mixed
Honor Roll RTTY
5BDXCC Plus 30,17,12
5BWAS
Stop the insanity!
Please do not add me to any distribution lists (Joke, Stories or Junk)
without my permission.
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|