Bill,
Sorry about that! I dont do metric conversions enough to remember correctly
sometimes. The 6.45 came from a conversion in a transformer equation and it
should have been divide by not multiply. The inches to mm factor is 25.4 (1
inch = 25.4 mm). From the example below 0.045" = 1.143 mm. The same equation
works, it's just you divide by, not multiply by in the end to convert from one
to another. However, for what you want leave dividing 25.4 off at the end and
it will be in mm. I know one thing, I'll have to stop trying to think when I've
been up so late.
BA = (0.0078 * T + 0.0174 * R) * No. of deg. in bend
14 Ga = 1.62814 mm
For 0" radius, 90 Deg bend in aluminum;
(0.0078 * 1.62814 + 0.0174 * 0) * 90
(0.01269949 + 0) * 90 =
0.01269949 * 90 = 1.14295428" or 1.14295428" / 25.4= 0.0449" (0.045") or for
ending pieces of flanges
Best,
Will
*********** REPLY SEPARATOR ***********
On 8/2/05 at 11:29 AM Bill Aycock wrote:
>Will-
>Where did the 6.45 come from? I think it is wrong.
>Bill
>
>At 07:14 AM 8/2/2005 -0400, Will Matney wrote:
>
>>Martin, I dont think much really changes as those factors are derived
>from
>>ratios. You should be able to add a multiplier of 6.45 to the formula to
>>get metric sums. Try that to see what you get and substitute MM in place
>>of the inch measurements then multiple the sum by 6.45. I think you'll
>get
>>the same just different measurment systems that way.
>>
>>BA = (0.0078 * T + 0.0174 * R) * No. of deg. in bend * 6.45
>>
>>Best,
>>
>>Will
>>
>>
>>*********** REPLY SEPARATOR ***********
>>
>>On 8/2/05 at 5:57 PM Martin Sole wrote:
>>
>> >Will,
>> >
>> >Thanks for the info, very useful. Do you have the formula in a suitable
>> >form
>> >for metric material? Haven't worked in imperial measurements for over 30
>> >years and only see it now and again on odd bits of US made kit.
>Actually I
>> >am going to make a new plenum for my second Alpha and the original is
>most
>> >certainly made to imperial measurements but nobody here would
>understand if
>> >I tried to replicate it that precisely so the new one will be made to
>> >metric
>> >dimensions. Would definitely appreciate the drawing and picture, mail
>away.
>> >
>> >Thanks
>> >
>> >Martin
>> >
>> >
>> >-----Original Message-----
>> >From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com]
>On
>> >Behalf Of Will Matney
>> >Sent: 02 August 2005 17:29
>> >To: amps@contesting.com
>> >Subject: Re: [Amps] Another metalwork question
>> >
>> >Martin,
>> >
>> >On bending steel, you use 1/2 the material thickness to figure how much
>to
>> >add in length. In other words you divide the material thickness in half
>> >where there would be an imaginary center line (its neutral axis) going
>> >trough it. Then when the steel is bent, a radius is formed on this
>> >imaginary
>> >center line even though the inside bend is a sharp 90 deg bend. So
>whatever
>> >the distance is around that small radius in the middle of the steel is
>the
>> >material to be added. Now aluminum is a different story and there is a
>> >formula for it too. What happens in aluminum, there is a shrinkage on
>the
>> >inside radius and a stretching on the outside different than steel. For
>> >aluminum see the formula and example below;
>> >
>> >BA = (0.0078 * T + 0.0174 * R) * No. of deg. in bend
>> >
>> >14 Ga = 0.0641"
>> >
>> >For 0" radius, 90 Deg bend in aluminum;
>> >
>> >(0.0078 * 0.0641 + 0.0174 * 0) * 90
>> >
>> >(0.00049998 + 0) * 90 =
>> >
>> >0.00049998 * 90 = 0.045" or about 3/64" or for ending pieces of flanges
>> >make
>> >it 1/16" from bend line to end.
>> >
>> >BA = Bend Allowance
>> >R = Radius of bend on the inside, not the neutral axis.
>> >T = Material thickness
>> >
>> >I have a pic with this and a drawing if needed I can e-mail it to you.
>Hope
>> >this helps.
>> >
>> >Best,
>> >
>> >Will
>> >
>> >
>> >*********** REPLY SEPARATOR ***********
>> >
>> >On 8/2/05 at 2:46 PM Martin Sole wrote:
>> >
>> >>Well it is actually amp related, or will be at some point I hope but
>> >>seeing how there is a great wealth of resource here it seems a good
>> >>place to start.
>> >>
>> >>Some time back I recall seeing an article, might have been in Radcom,
>> >>might have been in QST. Think it had to be either one of those two
>> >>though. It addressed the process of marking out metalwork for making
>> >>enclosures and explained how to allow the correct amount of material
>> >>for bends etc. Was within the last year or two I think.
>> >>
>> >>Just hoping that somebody might recall where this was or maybe point me
>> >>to another resource with similar information.
>> >>
>> >>Tks
>> >>Martin HS0ZED
>> >>
>> >>
>> >>
>> >>--
>> >>No virus found in this outgoing message.
>> >>Checked by AVG Anti-Virus.
>> >>Version: 7.0.338 / Virus Database: 267.9.7/60 - Release Date:
>> >>28/07/2005
>> >>
>> >>
>> >>
>> >>_______________________________________________
>> >>Amps mailing list
>> >>Amps@contesting.com
>> >>http://lists.contesting.com/mailman/listinfo/amps
>> >
>> >
>> >
>> >
>> >--
>> >No virus found in this incoming message.
>> >Checked by AVG Anti-Virus.
>> >Version: 7.0.338 / Virus Database: 267.9.7/60 - Release Date: 28/07/2005
>> >
>> >
>> >
>> >--
>> >No virus found in this outgoing message.
>> >Checked by AVG Anti-Virus.
>> >Version: 7.0.338 / Virus Database: 267.9.7/60 - Release Date: 28/07/2005
>>
>>
>>
>>_______________________________________________
>>Amps mailing list
>>Amps@contesting.com
>>http://lists.contesting.com/mailman/listinfo/amps
>
>Bill Aycock - W4BSG
>Woodville, Alabama
>
>
>_______________________________________________
>Amps mailing list
>Amps@contesting.com
>http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|