----- Original Message -----
From: "Bill VanAlstyne W5WVO" <w5wvo@cybermesa.net>
To: <amps@contesting.com>
Sent: Wednesday, August 11, 2010 6:01 PM
Subject: Re: [Amps] Replacing bias string diodes in Harbach rectifier board
Carl, the rectifier diodes that fused short were 2.5A (251Ds).
I have more questions:
(1) One of the other destroyed components in the bias path was a small SPST
relay that I used to bypass the 50Kohm cutoff self-bias resistor during
transmit and QSK keying. Since it was in SSB Tx mode when the arc occurred,
the contacts were closed, and they fused. I'm replacing this relay (which
was kinda noisy anyway) with a reed relay that will be silent as well as
even faster (< 2 ms). But I'd like to protect it from the same fate. I'm
thinking that if I want to protect the relay contacts, I will need a fuse in
the grid bias line. I'm thinking a 500 mA fast-blow fuse. Any reason this is
a bad idea? Or unnecessary?
** Coincidence but I just got thru replacing the similar purpose relay in
the LK-550 that also welded the contacts when the arc took out the 50W
zener. Would a fuse be fast enough to offer diode and relay protection? I
dont know but cant think of a reason not to try it. In my case replacing a
DPDT DIP relay on a PC board is a PITA but I get paid by the hour (-;
(2) In looking more closely at the converted 6m SB-220's RF output area and
comparing this with the original HF schematic, I see that there used to be a
pi-network filter in the B+ line consisting of an 8.5 µH choke flanked on
either side by 1000 pF 6KV bypass capacitors, one stud-mounted doorknob type
(closer to the tubes) and one radial-lead disc type (closer to the power
supply). The original choke was apparently removed during the 6-meter
conversion and replaced with a piece of wire; the capacitors are still
there. I doubt the wire (4") has enough inductive reactance at 50 MHz to
look like anything but a wire, so the two 1000 pF bypass caps are basically
just paralleled and become 2000 pF of B+ bypass capacitance. Between these
two capacitors, where the 4" wire now is, looks like an ideal spot to put
the glitch resistor, which will be four paralleled 82-ohm 10W Ohmite
vitreous enameled wire-wound resistors. I can also put the glitch resistor
between the rectifier PCB and the first bypass cap, which would get it a
little further away from the RF components. Would one position be better
than the other? Replacing the 4" wire with the resistors would be the most
convenient, as well as being better for getting them in the cooling air
flow.
** Thats the RFC I emphatically suggest be removed in any SB-220, stock or
converted to 6M. I also always suggest that it be replaced by a glitch
wirewound which does double duty absorbing any RF that gets around RFC-1.
Leave the caps in place.
(3) Regarding the tubes (3-500ZGs) -- I pulled them and tested them for
shorts using just a digital multimeter, and infinite resistance is shown
between cathode-grid and grid-anode. Is this a good indication that the
tubes escaped damage, or is this unpowered test relatively meaningless?
** Meters only shows a hard short Bill and many only show up with HV
applied. It is possible to blow the short open with a momentary application
of a 12V battery or even 120VAC if youre brave. Since this can also make
things worse but you already have a bad tube so its worth a shot. By
momentary I mean a glancing contact with a wire or similar.
Carl
KM1H
Bill W5WVO
New Mexico
--------------------------------------------------
From: "Carl" <km1h@jeremy.mv.com>
Sent: Wednesday, August 11, 2010 19:37
To: <dezrat1242@yahoo.com>; <amps@contesting.com>
Subject: Re: [Amps] 50 watt stud mount zener diodes
>
> ----- Original Message -----
> From: "Bill, W6WRT" <dezrat1242@yahoo.com>
> To: <amps@contesting.com>
> Sent: Wednesday, August 11, 2010 1:14 PM
> Subject: Re: [Amps] 50 watt stud mount zener diodes
>
>
>> ORIGINAL MESSAGE:
>>
>> On Wed, 11 Aug 2010 10:45:42 -0400, "Carl" <km1h@jeremy.mv.com> wrote:
>>
>>>A tube arc will take out a
>>>50W zener as fast as a 10W version.
>>
>> REPLY:
>>
>> More nonsense from our favorite supplier.
>>
>> A truly massive arc would take out either one, but an arc just big
>> enough to damage a 10 watt zener would do no harm to a 50 watt.
>>
>> 73, Bill W6WRT
>
>
> Its a shame that Bill is so insecure that he has to start off a reply with
> an insult. Perhaps if enough readers complain to our administrator he will
> take steps to remove him from this forum and we can get back to our normal
> discussions and even arguments with civility.
> If anyone needs that email address send me a direct request.
>
> I didnt realize that there were baby and big arcs once a plasma is
> created.
> IMO they range from big to bigger depending upon the PS capacity to
> destroy
> things before something opens up the AC or HV line.
> Since the event that started this thread destroyed 1A diodes (or were they
> 2.5A) and would also slam grid choke pi's together in a SB-220 then its
> pretty much a given that either size zener would also be history.
>
> The customer LK-550 I have on the bench had your basic 3-500 arc and the
> 50W
> zener was instant history.
>
> Carl
> KM1H
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|