Lunar Link runs a pair of 3CPX800's on 432; dont know about the filaments.
Im running a 3CX400U7 on 903, in a surplus Eimac cavity, which has an
annoying filament derating spec since its different for CW and SSB. Since it
came with the matching Motorola PS I havent bothered to measure the voltage,
its used on CW most of the time.
Carl
KM1H
----- Original Message -----
From: "Paul Decker" <kg7hf@comcast.net>
To: <amps@contesting.com>
Sent: Friday, June 17, 2011 9:00 AM
Subject: Re: [Amps] 8874/3cx400a7
>
>
>
>
> Interestingly enough, the 3cx800A7 and 3cpx800A7 sheets don't have that
> paragraph. I suspect because they are only spec'ed to 350 Mhz. On the
> other hand, the 3cx800U7 has a similar paragraph showing reduced heater
> voltages. It goes even further stating that the heater voltage should only
> be reduced when rf drive is applied and it should be returned back to
> normal when rf drive is removed.
>
>
>
> quote:
>
> Heater voltage should be returned to 13.5 volts simultaneously with the
> removal of rf drive. In low duty factor applications such as CW telegraphy
> and voice SSB, heater voltage shouldbe maintained at 13.5 volts.
>
> :end quote
>
>
>
> So maybe I shouldn't worry about it at all. Most of my operating is CW and
> SSB with the occasional FM and WSJT. I'm considering putting in a switch
> mechanism to switch between class AB and class C for FM and WSJT.
>
>
>
> Paul.
>
>
>
>
> ----- Original Message -----
> From: "Paul Decker" <kg7hf@comcast.net>
> To: amps@contesting.com
> Sent: Friday, June 17, 2011 8:20:41 AM
> Subject: 8874/3cx400a7
>
>
>
>
>
>
> A question I'm sure the experienced amp builders can answer. I was reading
> through the Eimac 8874 datasheet last night and found this paragraph:
>
>
>
> quote:
>
> HEATER/CATHODE OPERATION - The rated heater voltage for the 8873, 8874,
> and 8875 is 6.3 volts, as measured at the base of the tube, and variations
> should be restriced to plus or minus 0.3 volt for long life and consistent
> performance. At frequencies above approximately 300 MHz it may be
> necessary to reduce heater voltage to compensate for rf transit-time
> heating of the cathode after dynamic operation of the tube has started.
> The back heating is a function of frequency, grid current, grid-bias,
> anode current, duty cycle, and circuit design and adjustment. The
> following heater operating voltages are recommended:
>
>
>
> Frequency (MHz) Heater Voltage
>
> 300 or lower 6.3
>
> 301 to 400 6.0
>
> 401 to 500 5.7
>
> :end quote
>
>
>
> In my new 70cm amp, my heater voltage is set to 6.3 volts. Reading this,
> there are many variables to take into consideration of which there is no
> "formula" to figure out the ideal heater voltage. Should I simply reduce
> my heater voltage to 5.7 volts? What effect would this have on the
> amplifier performance? Does anyone have experience with lowering the
> heater voltage in this type of situation?
>
>
>
> Thanks,
>
> Paul
>
> kg7hf
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1382 / Virus Database: 1513/3708 - Release Date: 06/16/11
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|