Amps
[Top] [All Lists]

Re: [Amps] Measuring tank coil inductance

To: amps@contesting.com
Subject: Re: [Amps] Measuring tank coil inductance
From: Vic K2VCO <k2vco.vic@gmail.com>
Date: Thu, 25 Apr 2013 21:51:59 -0700
List-post: <amps@contesting.com">mailto:amps@contesting.com>
The GM3SEK spreadsheet allows for the influence of the plate choke. But if you compute the value of the tune capacitor without considering the choke, then you would not connect the choke while doing the inductance adjustment. Of course, then the capacitor will be in a slightly different place in operation.

On 4/25/2013 8:04 PM, Jim Thomson wrote:
Date: Thu, 25 Apr 2013 18:39:22 -0700
From: Bill Turner <dezrat1242@yahoo.com>
To: Amps <amps@contesting.com>
Subject: Re: [Amps] Measuring tank coil inductance

ORIGINAL MESSAGE (may be snipped):
On Thu, 25 Apr 2013 17:29:02 -0700, you wrote:

I made a temporary hookup which includes the tube, the plate choke, the 
bandswitch and the
pi-net components. I intend to set up the tank as follows:
REPLY:
If you're going to use the AADE unit to set the capacitance in-circuit, be
sure to disconnect the plate choke.

Bill, W6WRT

##  whoa.  A typ 90 uh plate choke on a  80-10m amp will  eat 10 pf  from the 
C1 tune cap on 80m..
A typ 180 uh plate choke will eat 40 pf  from the C1 tune cap on 160m band.

##  You can see that effect asap  when you wire in the load resistor  between 
anode and chassis...
with mfj  on the output.   Tweak tune and loads caps  for  1:1 swr on mfj.   
Then disconnect hot end
of each cap.... and measure how many pf each cap is.  This is all with the 
plate choke in the circuit, and
bypass cap from base of plate choke to chassis.

##  OK, then remove the plate choke, or disconnect  top end of plate choke.  
You will see asap that the
swr on the MFJ has jumped to 2:1   Retune the C1  tune cap to bring swr back 
down to 1:1

##  Disconnect hot end of C1 +C2 tune cap..and measure how many pf it is.   You 
will see that the C1  tune
cap has INCREASED in value.  On 80m,  with a 90uh plate choke used, it will 
increase by 10 pf.  On
160m, with a 180uh plate choke used, it will increase by  40 pf.   On 160m, 
with a 90 uh plate choke used.
it will increase by a whopping 80 pf.

##  The tune cap has to be increased a bit to cancel out the XL  of the plate 
choke on the lowest band used.
It will be less as you move higher in freq.

##    Hot ends of BOTH  tune and load caps  have to be disconnected,  to 
measure the C of each cap,
or else the two caps will be in parallel, and any lcr meter will  simply read 
the sum of the 2 x caps.

later......... Jim   VE7RF
via the tank coil between em.


_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

--
Vic, K2VCO
Fresno CA
http://www.qsl.net/k2vco/

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>