Frank,
Send the terminal command "OPER" only returns the current state. To have it
switch to OPR you have to enter 'OPER ON'
73
Jerry, NY2KW
-----Original Message-----
From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of Charlie Young
Sent: Wednesday, November 22, 2017 7:05 PM
To: frank.kirschner@gmail.com; amps@contesting.com
Subject: Re: [Amps] Alpha 87A Won't Key
Frank, you have to manually put the switch from standby to operate. If
there is a fault, the software will kick it back to standby mode even though
the switch is in operate, but to get it in operate mode you have to push the
switch.
It will not go to operate regardless of the switch position until the warm
up timer does its thing.
At least, this is the way it worked on the 87A I repaired.
73 Charlie N8RR
73 Charlie N8RR
Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows
10
________________________________
From: Frank Kirschner <frank.kirschner@gmail.com>
Sent: Wednesday, November 22, 2017 6:49:37 PM
To: Charlie Young
Subject: Re: [Amps] Alpha 87A Won't Key
Charlie and Jerry,
Thanks. That clarifies the situation.
When I enter "OPER" into the Alphamax software, it returns STATE = STANDBY,
so there is something keeping it from going into the operate mode. The
software should put it in operate mode regardless of the operation of the
STBY-OPR switch, so there is something more fundamental wrong. I may try a
call to Alpha on Friday.
Happy Thanksgiving.
73,
Frank KF6E
On Wed, Nov 22, 2017 at 6:24 PM, Charlie Young
<weeksmgr@hotmail.com<mailto:weeksmgr@hotmail.com>> wrote:
Frank, the amp should go to operate mode after the warm up delay if you push
the mode switch to operate.
It should go to operate mode regardless if the amp is keyed or not. It
won't go to operate mode unit the timer interval is up.
When it is in operate mode but not keyed, it is feeding through the antenna
to the receiver through the pin diodes. When you close the keying circuit ,
the pin diodes switch the amplifier to transmit mode. If it won't go into
operate mode the amp won't key to transmit.
There are a number of things which will keep the amp from going to operate
mode when the mode switch is changed from standby to operate.
The amp must be in operate mode before closing the input keying line will do
anything. If it is not going into operating mode, there is some other
issue.
That no faults are showing is a good thing.
The 87A is known for having contact resistance issues on the molex pins
which connect the wiring harness to the various boards. This is a very
common problem. I would start by opening up the amp and unplugging each of
these
plugs and reinserting it on the male pins a few times. A bit of Deoxit
spray on each connection might help.
73 Charlie N8RR
Sent from
Mail<https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgo.mi
crosoft.com%2Ffwlink%2F%3FLinkId%3D550986&data=02%7C01%7Cweeksmgr%40hotmail.
com%7C41c138effb6a443372cc08d53203b4aa%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C
1%7C0%7C636469913844889483&sdata=QF23PU4TR1ytgs99O4MAbkBTDEUEwBSg1G9Zf%2BclL
7k%3D&reserved=0> for Windows 10
________________________________
From: Amps <amps-bounces@contesting.com<mailto:amps-bounces@contesting.com>>
on behalf of Frank Kirschner
<frank.kirschner@gmail.com<mailto:frank.kirschner@gmail.com>>
Sent: Wednesday, November 22, 2017 4:28:37 PM
To: amps@contesting.com<mailto:amps@contesting.com>
Subject: [Amps] Alpha 87A Won't Key
The Alpha 87A I got in the ARRL auction won't key up.
I connected to the RS-232 port satisfactorily, and it showed no faults. I
have the transceiver RF out connected to the RF input of the amp, the RF
output of the amp connected to an antenna (TH-11), and a relay connected to
the keying relay input.
I checked the relay input, and it does short to ground when the transceiver
goes to transmit. But the amp stays on SDBY, and the OPR light doesn't come
on.
Is there something I just don't know to do? I've never used a
microprocessor-controlled amp before, so there may be a trick to it.
I'm on 20 meters, so I assume it isn't a 12-10 meter lock-out thing.
Thanks.
73,
Frank
KF6E
_______________________________________________
Amps mailing list
Amps@contesting.com<mailto:Amps@contesting.com>
https://nam02.safelinks.protection.outlook.com/?url=http%3A%2F%2Flists.conte
sting.com%2Fmailman%2Flistinfo%2Famps&data=02%7C01%7Cgeorgekwatson%40hotmail
.com%7Ce6ca0897e256445c4b4008d531f04d0d%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7
C1%7C0%7C636469830528935308&sdata=82qcEd1ZC5z0X%2BP6Qq8Qh7ahCeXTQXxPJ7CV1kaZ
B0g%3D&reserved=0
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|