Karlnet
[Top] [All Lists]

Re: [Karlnet] FCC certs and 100/200mw cards - possible group effort?

To: <karlnet@WISPNotes.com>
Subject: Re: [Karlnet] FCC certs and 100/200mw cards - possible group effort?
From: "Norm Young" <npyoung@applegatebroadband.net>
Reply-to: karlnet@WISPNotes.com
Date: Fri, 17 May 2002 09:52:02 -0700
List-post: <mailto:karlnet@WISPNotes.com>
Not a bad idea.  As has been said before, it would be nice to get a
contribution from the antenna manufacturers, as they stand to benefit also
from increased sales.  But a good idea, instead of waiting for the dreaded
FCC knock...

Norm

----- Original Message -----
From: "Dan Metcalf" <danm@suncorstainless.com>
To: <karlnet@WISPNotes.com>
Sent: Friday, May 17, 2002 9:11 AM
Subject: [Karlnet] FCC certs and 100/200mw cards - possible group effort?


> How about we put together a list of possible radio/antenna combos that we
> want to use and split the costs for fcc certs?
>
> Dan Metcalf
> Wireless Broadband Systems
> dan.metcalf@wbsysnet.com
> 781-658-2075
> www.wirelessbroadbandsystems.com
>
> -----Original Message-----
> From: Norm Young [mailto:npyoung@applegatebroadband.net]
> Sent: Friday, May 17, 2002 12:00 PM
> To: karlnet@WISPNotes.com
> Subject: Re: [Karlnet] higher power cards, what works, what doesn't
>
> Dan, I'm using a PRISM II card I got from Tony (it's a Senao,
> http://www.senao-usa.com/SL-2011CDEXT.htm).  Had some initial problems
with
> it in my PtMP  (I think I may have some problems with connectors or with
the
> antenna itself) side, but switched over to the PtP side (I have an 18 mile
> backhaul) and it seems to be working quite well.  (I'm surprised that
> reflected RF, if that is what it was, would cause the card to fruit-out
like
> it did.  Rx sensitivity went to hell, and there were problems doing remote
> reboots on the AP.)
>
> Norm
>
> ----- Original Message -----
> From: "Dan Metcalf" <danm@suncorstainless.com>
> To: <karlnet@WISPNotes.com>
> Sent: Friday, May 17, 2002 8:08 AM
> Subject: [Karlnet] higher power cards, what works, what doesn't
>
>
> > How many people out there are using the 100mw & 200mw cards w/ Karlnet
> > v4.02? what works what doesn't? I couldn't get the symbol24 card to
work.
> > Also when you setup the rg1000 do you tell it what type of card is in
the
> > interface or do you leave it at default?
> >
> > Dan Metcalf
> > Wireless Broadband Systems
> > dan.metcalf@wbsysnet.com
> > 781-658-2075
> > www.wirelessbroadbandsystems.com
> >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> >
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>


<Prev in Thread] Current Thread [Next in Thread>