Karlnet
[Top] [All Lists]

RE: [Karlnet] FCC certs and 100/200mw cards - possible group effort?

To: <karlnet@WISPNotes.com>
Subject: RE: [Karlnet] FCC certs and 100/200mw cards - possible group effort?
From: "barrywhitcomb" <barrywhitcomb@msn.com>
Reply-to: karlnet@WISPNotes.com
Date: Fri, 17 May 2002 12:26:50 -0400
List-post: <mailto:karlnet@WISPNotes.com>
We've been testing 2 cards (200 mW) from MikroTik with some Poynting
antennas (8 & 13 dpi Patch and 12 dbi Yagi) and have been pleased, so
far. 

Barry Whitcomb

-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]
On Behalf Of Dan Metcalf
Sent: Friday, May 17, 2002 12:12 PM
To: 'karlnet@WISPNotes.com'
Subject: [Karlnet] FCC certs and 100/200mw cards - possible group
effort?


How about we put together a list of possible radio/antenna combos that
we want to use and split the costs for fcc certs?

Dan Metcalf
Wireless Broadband Systems
dan.metcalf@wbsysnet.com
781-658-2075
www.wirelessbroadbandsystems.com

-----Original Message-----
From: Norm Young [mailto:npyoung@applegatebroadband.net]
Sent: Friday, May 17, 2002 12:00 PM
To: karlnet@WISPNotes.com
Subject: Re: [Karlnet] higher power cards, what works, what doesn't

Dan, I'm using a PRISM II card I got from Tony (it's a Senao,
http://www.senao-usa.com/SL-2011CDEXT.htm).  Had some initial problems
with it in my PtMP  (I think I may have some problems with connectors or
with the antenna itself) side, but switched over to the PtP side (I have
an 18 mile
backhaul) and it seems to be working quite well.  (I'm surprised that
reflected RF, if that is what it was, would cause the card to fruit-out
like it did.  Rx sensitivity went to hell, and there were problems doing
remote reboots on the AP.)

Norm

----- Original Message -----
From: "Dan Metcalf" <danm@suncorstainless.com>
To: <karlnet@WISPNotes.com>
Sent: Friday, May 17, 2002 8:08 AM
Subject: [Karlnet] higher power cards, what works, what doesn't


> How many people out there are using the 100mw & 200mw cards w/ Karlnet

> v4.02? what works what doesn't? I couldn't get the symbol24 card to 
> work. Also when you setup the rg1000 do you tell it what type of card 
> is in the interface or do you leave it at default?
>
> Dan Metcalf
> Wireless Broadband Systems
> dan.metcalf@wbsysnet.com
> 781-658-2075
> www.wirelessbroadbandsystems.com
>
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com 
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>

_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet


<Prev in Thread] Current Thread [Next in Thread>